Nissan Sentra Front & Rear 6 Piece Suspension Kit TRQ SKA67269

Underneath the vehicle, I want to support this part of the rear suspension. This is basically a lower control arm. It is connected to the other side. So if you're doing both rear shocks, you can support both at the same time or you could even drive the vehicle up onto ramps on the back. You don't have to take off the rear tires to do this job.

Now I'm gonna use an 18-millimeter socket, take this bolt out. In the trunk of the vehicle, it's a little bit easier to access from the back seat. Fold the back seat down. Right here, this is a little cover. Take that cover off. Take this little cover off right there. And there's a nut right on top, take that nut off.

So to prevent the shaft from spinning, you can use a 16-millimeter wrench for the nut. And then for the top of the shaft, use a 5-millimeter wrench. It's not gonna be easy to get in there, but. It might be slightly easier to use a 16-millimeter ratchet wrench and some locking pliers. Just try not to get on the threads. There we go. And loosen it up. Just use some smaller locking pliers if you can. And try to take that nut off. And when the nut comes off, the shock is gonna fall down. Take that washer out, that bushing out. There's the nut.

Here's the old shock. Just take this cover off, the bumper's in there and we'll reuse this. Now with the new one, we're just gonna exercise it, do it three times. Take the cover, slide that over. Take this washer and this bushing and this pin. Make sure these came out of the old one before you slide this in and then up on top, you're gonna do the same. If you slide this in position, this is gonna go down and then you have your nut.

Then take the shock and slide it in position right here. And then it's best if you have a friend hold this for you while you put the nut on top. All right, take the bushing, put the bushing on first or the mount and take this washer and get the nut started. Now I'm going to take a 14-millimeter ratchet wrench and I'll use some locking pliers to hold the stud, hold the shaft from spinning. And tighten it up. Once it's snug, if you can get a torque wrench in there with a 14-millimeter socket, you can tighten that nut to 15 foot-pounds. Take this cover, put this back on. That's good. Close this up just like that. And then pull the shock down. Try to get the bolt hole lined up. This might be a little bit tricky. What you could do is put some extra weight in the trunk and that'll weigh this down a little bit. That's good. And tighten the bolt up. Torque that bolt to 64 foot-pounds.

You wanna keep in mind, when you're doing this job, after you're done, you're gonna wanna go to a local garage and have the vehicle aligned so you don't have premature tire wear. Take the wheel off. I'm going to use a 21-millimeter socket. Remove the wheel. I'm just going to spray a little rust penetrant on here, this is pretty rusty. Let it soak. I'm going to take this nut off using 18-millimeter wrench, and then to hold the stud I'm gonna use a 6-millimeter hex bit. Loosen this up first. And take that nut off, and then slide this out. And take the ABS wire out of this bracket right here, just slide it out. And this one too. And we want to remove the brake hose from this bracket, there's a little clip right here, just take a screwdriver, just try to pry it out a little bit. Slide that off and slide the brake hose out. Now I'm going to use a 21-millimeter wrench on this bolt here and 21-millimeter socket, take these two nuts off. Be careful with the brake hose, don't get it caught. Don't want to rip it. And then you can take these bolts out. And slide the knuckle off of here. You might want to support this knuckle, you don't want to put too much tension on the brake hose or on the CV joint, if it start pulling out.

And we need to take these bolts out, but before we take these two out, there is a third one that's behind the cowl, right here. You can just take a straight blade screwdriver, raise this up right here. Take this out of the way. And then there's a little cover right here, pull this up and out of the way, and then you can access it. I just take a 13-millimeter socket and an extension, then I pull this cover off so I can access it from here with my hand, just to get on it and loosen it up. And pull the other two out. Now I'm going to grab the strut assembly from underneath and take this last bolt out. And I'll pull it right up. All right. Take the new strut assembly. Now, this only goes on one way, these bolt holes will only line up one direction. So, slide this in position. Then you can get one of these bolts started. It might be easier if you have a helper hold that while you get the bolt in. And get this other one in. Just make sure you get a couple turns on these bolts. I am going to leave this loose so that we can attach everything underneath first before we torque these down.

Now, take the knuckle, slide this in position. If you have to twist the strut, you can. And raise it up. Slide the bolt there. And this one right here. And now we'll torque these to 92 foot-pounds. Line the brake hose up. Take the clip, slide the clip in position, and just take a hammer and just give it a tap. There we go. Looks good. Take the ABS wire, put that back in the bracket right there and right there. Reattach the upper sway bar link. Put the nut on. Now we'll torque this to 62 foot-pounds. And then line these bolts up to kind of where they were before, there is an alignment adjustment right here. I'm going to use a 12-millimeter socket to tighten these down. And then torque these to 12 foot-pounds. And put these covers back on, here and right here. Put the wheel back on, and the lug nuts. Now I'm going to torque these lug nuts to 83 foot-pounds in a star pattern to tighten the wheel down evenly. Just go around again, double check.