Replaces
This part doesn’t fit a . Select from parts that fit.
Light Assembly Lifetime Warranty
Frequently bought together
Part Details
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
The bulbs are for testing and not covered under our warranty. Our warranty applies to the light assembly only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
I want to take these two pins out, just slide this pin forward just like that. Slide it out. Do the same on this one. And then just slide the light forward. Now, you can disconnect the connector right there, just like that. Or you could also slide the bulb out, twist it, slide it out. Just don't touch the bulb if you're going to reuse it. It's always a good idea to replace the bulbs at this time. Put the new bulb in here. This one is an HB4, that's for the low beam. And the high beam is an HP3. That's good. Just connect the connectors. And just line this up. When those holes are lined up, take the pins. Before I lock it in place, just get the other pin lined up. Might have to wiggle it back and forth a little. All right. With both of those lined up, lock them in place. To aim the headlights, you can use this right here. You just use an E8 socket and you can twist it left and right. And that's gonna move it side to side. And for the height adjustment, you're going to go down here. The same E8 socket, or you can also use a Phillips head screwdriver.
This is going to be a general tutorial on how to aim your brand new TRQ headlamp assemblies. Okay. So, looking at your brand new TRQ headlamp assembly, you're going to see where your low beam is, and you'll see a little dot right in the center. And that is the axis point, okay? So, what we're going to do is we're going to mark that with an erasable marker, just so it's easier to see. Next, what we need to do is measure from the level ground up to this point and take note of that measurement. Now, we're just going to pull the car up to our wall. On our vehicle, we remember that the measurement was 28 inches for our axis point. Your vehicle may be different, but that's where I'm going to put this tape. Just above that 28 inches. We'll do the same on the other side. Okay. So, let's just back the vehicle up straight back 25 feet from the wall. And now, that we moved our vehicle 25 feet back from the wall, we're going to start with our measurement here. That's where the headlamp center is. We're gonna go down 4 inches on the driver side. On the passenger side, we have our line here. What we need to do is go down 2 inches. To adjust the driver side. We're going to cover our passenger side headlamp. If you look at the backside of your headlamp assembly, you're going to see something that looks like this. This is the adjustment. Some of these headlights assemblies have one, two, or even more of them, but you should at least have one. This is how we're going to adjust the headlight beam. Now, we're gonna lower the top part of the beam down to just below this line. When you turn the adjustment to the right, it brings the beam up. And if you turn it to the left, it'll bring the headlight beam down. And this is this way on most vehicles. Let's continue on to doing the passenger side. All right. We properly aligned our TRQ headlamp assemblies. Okay. And on the quality TRQ headlamps for a pickup truck, the procedure is going to be the same. You're going to find your center dot, mark it, and then you'll measure from the level ground up to your dot.
So, once your headlamps are properly adjusted, it'll be time to adjust your fog lamps. You'll notice on the driver side, the focal point is all the way at the bottom right now. I would like to bring it up so it meets up with approximately the bottom of the focal point of the headlight. Some fog lamps have an adjuster, others don't. The ones that do have an adjuster, you would just turn the adjustment to the left or to the right to adjust the beam up and down to where it needs to be. Now, with your TRQ headlamps and fog lamps properly aligned, you can drive down the road safely.
Tools used
This video is brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, my name's Mike Green. I want to help you save time and money repairing your vehicle. I have 20-plus years experience restoring and repairing cars and trucks. My company, 1A Auto, sells high quality replacement parts over the Internet. In this video, I'll be showing you how to install these parts. By the end of this video, you'll know how to install them and where to get them. That's going to save you time and money. Thank you and enjoy the video.
This video, we'll be replacing the headlight on a 2004 GMC Sierra, basically the same as a '99 to '06 Sierra. It is a pretty easy process. It requires no tools. So, with that, we'll get you to it.
There are two pins that hold the headlight in right there and there, and you'll twist those out and pull them up. Then, the headlight basically comes right out. Then, once it's out, you can reach in behind and unplug the lights. They're basically just little teeth that you can kind of pull with your thumb, and they unplug.
Okay, now we're going to replace the headlight. At this time, you can obviously service the bulbs if that's all you're looking to do. So, they just twist in ... or twist out and twist back in. Then, our headlights come with that whole bracket and everything, so if you're replacing your headlights at this point, you're plugging them in and then everything should install just the same way. Plug them in, put the headlight back in there. Take your pins, put them down through. Obviously you have to make sure that the headlight is all the way back in and lock them into place, and your head light's all set.
Now, we'll do a quick test. Just make sure everything's working. The headlight, the high beam, and the signal are not working. Actually that side marker's not working, so we'll really quickly replace that, and then, you're all set. Hope this helps you out. Headlights are pretty easy to service on these GMC trucks.
This video was brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Feel free to call us toll free 888-844-3393. We're the company for you on the Internet, and there for you in person too. Thank you very much.
