/2004 Ford Expedition To 12/01/03 Production Date without Air Suspension Front Driver & Passenger Side Upper 2 Piece Control Arm with Ball Joint Set TRQ PSA62375
1ASFK01200-Ford Expedition Front Driver & Passenger Side Upper 2 Piece Control Arm with Ball Joint Set TRQ PSA62375
2004 Ford Expedition To 12/01/03 Production Date without Air Suspension Front Driver & Passenger Side Upper 2 Piece Control Arm with Ball Joint Set TRQ PSA62375
Kit Includes: (1) Front Passenger Side Upper Control Arm with Ball Joint (1) Front Driver Side Upper Control Arm with Ball Joint
Specification
Side Location
Driver & Passenger Side
Build Date
To 12/01/03 Production Date
Steering / Suspension Option
without Air Suspension
Location
Upper
Front
Our control arms are designed to be direct replacements for the original factory parts. They are 100% brand new and require no modifications for installation. No special tools are required because all of the bushings come pre-installed.
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
How To Replace Outer Tie Rod 2004-08 Ford F150
Created on:
Tools used
Adjustable Wrench
Torque Wrench
Hammer
Jack Stands
Grease Gun
21mm Socket
Measuring Tape
Bearing Grease
21mm wrench
7mm Socket
10mm Socket
Ratchet
Floor Jack
1. Removing the Wheel
Pry off the center cap with a flat blade screwdriver
Loosen the lug nuts with the vehicle on the ground
Raise the vehicle with a floor jack
Secure the vehicle on jack stands
Remove the lug nuts
Pull off the wheel
2. Removing the Outer Tie Rod
Turn the wheel by hand
Remove the 21mm nut from the outer tie rod
Thread the 21mm nut on a couple of turns
Hold the tie rod with an adjustable wrench
Loosen the tie rod adjusting nut with an adjustable wrench
Strike the steering knuckle with a hammer
Twist the 21mm nut off the tie rod
Measure the distance from the tie rod boot to the outer tie rod stud
Note that measurement
Twist off the outer tie rod.
3. Installing the Tie Rod
Twist on the outer tie rod
Measure the distance from the tie rod boot to the outer tie rod stud
This should be the same as the distance noted in Step 2
Move the adjusting nut as necessary
Push the tie rod into the wheel knuckle
Fasten the 21mm nut onto the tie rod
Tighten the 21mm nut to 111 foot-pounds of torque
Tighten the adjusting nut
Twist the grease fitting into the tie rod
Tighten the grease fitting with a 7mm socket and ratchet
Add grease to the grease fitting with a grease gun
4. Reattaching the Wheel
Slide the wheel into place
Start the lug nuts by hand
Tighten the lug nuts preliminarily
Lower the vehicle to the ground
Tighten the lug nuts to 120 foot-pounds in a crossing or star pattern
Reattach the center cap
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace an outer tie rod on this 2005 Ford F150. We show you on the driver side but the passenger side is the same procedure. The items you'll need for this is a new outer tie rod from 1AAuto.com; a 7, 10, and 21mm socket and ratchet with a piece of pipe for leverage; two adjustable wrenches; a tape measure; a hammer; a torque wrench; and jack and jack stands.
Start off by prying off the hub cap. Then loosen up these lug nuts using a 21mm socket and ratchet and a piece of pipe for some extra leverage. Once you get each of them loosened up you can raise the vehicle and remove them the rest of the way. Now pull the wheel off.
Now turn the wheel and then remove this 21mm nut at the top of your outer tie rod. Then once you remove it, you want to just put it back on just a couple threads. Spray the nut at the end of your outer tie rod with some penetrating fluid, and then, using two adjustable wrenches, just loosen it up. Now hammer the knuckle until the outer tie rod drops down. Now you can remove that nut and just set your outer tie rod off to the side.
Now measure from the boot on your inner tie rod to the center of your outer tie rod, and just remember that distance. Then you can twist your outer tie rod free. We'll fast forward as Mike does that.
On the left is the old outer tie rod. On the right, is the new one from 1A Auto. You can see they're identical and they'll fit exactly the same. Take your new outer tie rod and twist it into place. We'll fast forward as Mike does that. Now, measure from the boot to the inside of the outer tie rod and make sure it's the same distance. If it is, you're all set. If not, you'll have to move that nut to adjust it.
Now, feed your outer tie rod up through the wheel knuckle and replace that nut and tighten it up. If the studs start spinning when you use your 21mm socket just use a 21mm wrench and a 10mm socket to hold the stud in place and tighten it up. Then torque that to 111 foot pounds.
Now, using two adjustable wrenches just tighten that nut back up, and then put your grease fitting into place on the outer tie rod. Then just tighten it up with a 7mm socket and ratchet. Using a grease gun, just top it off with some grease.
Now we'll fast forward as Mike replaces the wheel, and replaces the lug nuts, and tightens them preliminary, and then lowers the vehicle and tightens them the rest of the way. Then torque each of them, in a crossing pattern, to 120 foot pounds. Then just replace your hub cap and you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
PSA62375
In Stock
Product Reviews
Loading reviews
4.43/ 5.07
7 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
6
0
0
0
1
Excellent
Chad
April 9, 2019
Fast and accurate delivery. Parts were as described. Highly recommend.
Driveway Mechanic
Kevin
April 13, 2019
The front control arms were shipped within a few days.
They fit perfectly, ride well and looked like the originals.
These were the lowest price I could find on the internet.
Hope they last, time will tell, I will update my review if they don't.
Upper Control Arms
Z
August 24, 2019
Good prices,fast shipping and quality parts.Great fit easy to install.Great to deal. People were friendly and easy to talk to on the phone.
Complete customer care;
C
May 23, 2020
I am completely satisfied with all 1A Auto services. Long story short, I made two orders for auto repair parts, the suspension parts for the front of the vehicle worked out perfectly because fortunately I ordered them correctly LOL and the parts perfectly manufactured for my vehicle worked without complication. On the second order I misread the description on the part and accidentally ordered the front wheel bearing hubs instead of the rear and had to do a return, and that too has been seamless and without complication so far.
Garbage
Christian
October 15, 2020
They broke a week late and they were installed by a mechanic you get what you pay for
Perfect fit
Jimmie
March 14, 2021
Replaced both upper control arms, both lower ball joints and both outer tie rod ends. Everything arrived quickly and well packaged. All parts fit perfectly. 2003 Ford expedition. My sister is very satisfied and so am I.
Guillermo
April 20, 2023
Excellent good quality fit exactly 2003 ford expedition ; thank you!
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Ford is a registered trademark of Ford Motor Company. 1A Auto is not affiliated with or sponsored by Ford or Ford Motor Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.