Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Part Details
Install Tip: When replacing steering components, have a professional alignment performed afterwards. This ensures proper tracking and even tire wear.
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the outer tie rod end on this 2008 Dodge Ram 1500. This is for a non-mega cab truck. We're doing the passenger side, but this information will be exactly the same on the driver's side.
Here are the item's you'll need for this repair: 22-27mm socket, 1/2 breaker bar, ratchet, socket extensions, breaker bar, 24mm wrench, torque wrench, jack and jack stands.
With the vehicle on the ground, using a 22mm socket and a breaker bar, break the lug nuts for your wheel loose. These chrome lug nuts tend to be swollen, so make sure your socket's on there good. Once your lug nuts are loose, raise and support the vehicle with a jack and jack stands.
This wheel and tire assembly, being a big off road tire and 20 inch wheel, it's going to be real heavy, so we're only going to bring it up a little bit when we take it off. Remove the wheel and tie from the hub.
The tie rod end is located at the end of the inner tie rod and bolts into this spindle. We're going to use a 24mm wrench to break the lock nut loose just a little. Use a 22mm deep socket and a ratchet to remove the nut on the bottom. Going to hit the side of the spindle to release the tie rod. After a few good hits, should be able to knock it out of the spindle. Remove the tie rod end from the spindle and unthread it from the inner tie rod.
Here we have our old part that we removed from our 2008 Dodge Ram. Here we have our new tie rod end from 1AAuto, part number 1ASTE00402. As you can see, they're very similar, some minor differences in the aesthetics, but the actual stud to go into the spindle is correct. They have the same size threads. They're the same length. Our new part comes with a castle nut and a cotter pin, which is more secure than the factory flange nut.
Some symptoms of a bad tie rod end can be play in the steering wheel. Could also cause an unusual tire wear pattern or you can feel that you may need to use a lot more force than you're used to when trying to turn the wheel. If your vehicle is suffering from any of these symptoms and you've deduced that it's the tie rod end, this new part from 1AAuto is going to go in, direct-fit, just like your original equipment, and fix you up right.
Thread the new tie rod end onto the inner tie rod. We'll reinstall it into the spindle. Start the new castle nut on, tighten it down with a 27mm socket and ratchet. Torque to 45 foot-pounds, then add an additional 90 degrees. Install the cotter pin, then the long tab down under the bottom of the bolt. Cut the short end off flush.
Using a 24mm wrench, tighten the lock nut on the inner tie rod back against your outer tie rod end. Start your lug nuts by hand. Tighten the lugs as far as you can. Remember to bring the wheel down evenly and always tighten in a cross pattern. Once the lugs are as tight as you can get them with the tire in the air, put partial weight of the vehicle on the ground by lowering it off your jack stands. Torque your lug nuts to 135 foot-pounds in a cross pattern. Bring the vehicle for a professional alignment.
Thanks for tuning in. We hope this video helped you out. Next time you need parts for your car, please visit 1AAuto.com. Also check out our other helpful how-to and diagnosis videos.
Tools used
Okay, friends. To get started on this vehicle, the first thing we wanna talk about is safety. You want hand and eye protection. Secondly, you wanna make sure that you raise and support the vehicle by the frame so the suspension's hanging. Next, let's remove our lug nuts. Remove your wheel. Now that we have the wheel off, we have a nice, clear view of our tie rod ends. Just a quick note, whenever I'm replacing tire rod ends, I usually like to do them as a pair. With that said, let's break free our jam nut.
Here we are. Let's get our locking cotter pin out of here. There we are. Let's go ahead and remove this nut. Put that back on a couple of threads. The next thing we're gonna do is separate the tie rod end from the knuckle itself. You can do that with a couple loving bonks with a hammer. Unscrew the outer tie rod end and make sure you count the threads as you come off, one, two, three, and so on. Twenty-two for me. Time to put on the outer tie rod end. Make sure you put on as many turns as you did to remove the original, one, two, three, and so on. That should line up perfectly. If it doesn't, you might've moved this a little bit or you might be off. Snug this up, torque this to 45 foot-pounds. Now we need to take a look and make sure that the slotted area of our nut lines up with the hole in the tie rod stud. If it doesn't, you need to continue tightening until the first one does. Go ahead and peen that over.
Now it's gonna be time to tighten our jam nut. To do that, you wanna hold your tie rod so it can't spin because you don't wanna damage the ball and socket area. Now let's go ahead and snug this. There we go. If your tire rod's crooked, just make sure you straighten it out so it's level with the ground. Go ahead and put the wheel back up on here. We're gonna start all of our lug nuts and then we'll torque them to 130 foot-pounds.
Tools used
Okay, friends, to get started on this vehicle, the first thing we wanna talk about is safety. You want hand and eye protection. Secondly, you wanna make sure that you raise and support the vehicle by the frame so the suspension is hanging. Next, let's remove our lug nuts. Remove your wheel. Now that we have the wheel off, we have a nice, clear view of our tie rod ends. Just a quick note, whenever I'm replacing tie rod ends, I usually like to do them as a pair. With that said, let's break free our jam nut. Here, we are.
Let's get our locking cotter pin out of here. Here we are. Let's go ahead and remove this nut. Put that back on a couple of threads. The next thing we're gonna do is separate the tie rod end from the knuckle itself. You can do that with a couple loving bonks, with a hammer. Unscrew the outer tie rod end and make sure you count the threads as you come off, 1, 2, 3 and so on. 22 for me. The next thing we need to do is remove our jam nut from our inner tie rod end. I'm gonna hold that inner tie rod end with some locking pliers.
Next, we're gonna remove the clamp that holds our Bellows boot to the inner tie rod end. So now if you follow your boot towards the inside where your power steering rack is, you're gonna find that there's a little lip right here. You're gonna wanna just kind of have a nice pry bar like this and a hammer, and we're gonna break that free. It's not reusable, so you're gonna have to replace it with something different. Now, let's go ahead and grab onto that boot. Give it a nice twist to break it free. And we're gonna try to pull it off of the inner tie rod end. There it is.
Double check your boot, make sure it's not worn or torn in any way. If it is, you'd wanna replace it, this one looks great. Now we have to unscrew our inner tie rod end from the rack itself. To do that, you can use a tool that looks like this. It's just gonna go around the bobble down here. Or of course you can use pliers or even a wrench. Whatever you need to do, unscrew it. Okay let's get this off of here. Now that that's off, I always like to clean up the mess that might be around the area, clean up the threads and then of course around it. Time to start in our new inner tie rod end. I like to use a little bit of threadlocker, but we'll call it your prerogative.
Once you have it bottomed out, just make sure you go ahead and give it a little snug. Your inner tie rod end came with some grease. You're gonna use that right along this area right here and then a little bit on the inner tie rod and shaft. I like to use a nice brush I don't like to get it on my hands. Just pack it right in there and make sure it's nice and lubricated and then some right up along this groove right there. That's where the boot's gonna sit. This is gonna help your alignment be professional. The next thing we need to do is prepare our boot so it can be mounted. Take a nice wire tie, I'm just gonna start right on here. Here we are, not too tight. Do the same on the other side, if you're not reusing your clamp, take your boot. We're gonna slide it right on there. Slide it over the rack so you're sure it's nice and secure. That feels good.
We're gonna slide this forward end so it goes over that little lip. You can see it right there, put it right up against it. Perfect. Make sure your boot's sitting perfectly on the rack. And now we're going to snug everything up. Trim from off the excess. Next, we're gonna put a little bit of grease or copper, never seize on the threaded area here. Go ahead and put on your jam nut, put it halfway down the threaded area. Time to put on the outer tie rod end. Make sure you put on as many turns as you did to remove the original 1, 2, 3, and so on. That should line up perfectly. If it doesn't you might've moved this a little bit, or you might be off. Snug this up, torque this to 45 foot-pounds.
Now we need to take a look and make sure that the slotted area of our nut lines up with the hole in the tie rod stud, if it doesn't, you need to continue tightening until the first one does. Go ahead and pin that over. Now, it's gonna be time to tighten our jam nut. To do that, you wanna hold your tie rod so it can't spin because you don't wanna damage the ball and socket area. Now let's go ahead and snug this. There we go. If your tie rods crooked, just make sure you straighten it out so it's level with the ground. Go ahead and put the wheel back up on here. We're gonna start all of our lug nuts and then we'll torque them to 130 foot-pounds. Torqued.
