Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Part Details
TRQ suspension kits are manufactured using premium raw materials and coatings for extended service life. Each TRQ suspension component is designed to be a direct, maintenance-free replacement to the stock unit. To extend the life of your steering and suspension components, TRQ recommends replacing components in pairs, sets, or kits. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Replacing struts used to require specialized tools to compress, remove, and transfer the old spring and mount. Our Pre-assembled, complete strut & spring assemblies come with all new parts and make the job much quicker and easier for the do-it-yourself mechanic.
Strut & spring assembly contains:
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace a front stabilizer link on this 2007 Pontiac G6. It's the same as any 2005 to 2010 G6, as well as the Saturn Aura. Not a difficult procedure. You will need jack and jack stands, and you'll want to jack up both front wheels off the ground and support it with jack stands. Then you'll need a lug wrench or a 19mm socket with a ratchet, maybe even a breaker bar and a pipe for some extra leverage. Then, after that, you'll just need two 18mm wrenches, one of those 18mm will have to have an open end.
Start out by using just a socket to loosen the lug nut covers, or the wheel cover as in this case. We're going to use impact or air tools sometimes. If you don't have the benefit of air tools, just start with the vehicle on the ground, loosen the lug nuts, then raise and secure the vehicle, and move the lug nuts from the wheel and tire.
Use an 18mm wrench to grab on to the nuts, part of the stud of the stabilizer link, and then use an 18mm socket, loosen up the nut, and then it comes off. Here's the fun part of the repair. You pull that down out of the way, and you can see the other end of the link right there. Put the 18mm wrench on the nut that's in the shaft, just like before. Then, there's not really enough room to get a ratchet back in there, so you basically just have to take a wrench and slowly, carefully, one eighth of a turn at a time, and I'll fast-forward the video as we do that.
Then, just reinstall the link as you took it apart. Go ahead and speed up as we tighten up that lower nut, and like I said before: it's not all that difficult; it just takes quite a bit of time because you can't move that nut too far each time.
Bring the sway bar link back into place, and should you possibly feel the need to replace those sway bar links, at 1AAuto.com, we sell those as well. But then use a 18mm wrench and an 18mm socket and ratchet to tighten up that bolt. And that bolt should be tightened somewhere around 70 to 75 foot-pounds. Put the bracket that holds your brake hose back into place, and start the 10mm bolt on and tighten it up.
Reinstall the wheel. Put the lug nuts on by hand first just to make sure you don't cross thread them, then tighten them preliminarily. Put the vehicle on the ground, torque the lug nuts to 100 foot pounds using a star pattern. Now, reinstall your hubcap and we're going to do that with that 19mm socket. I'm just going to screw them in by hand. Also, we want to make sure you line up the valve stem with the notch in the hubcap for the valve stem. I'll go ahead and fast-forward through that.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Okay, friends, before we get started, the first thing that I want to mention is you want to be safe. So have hand protection and eye protection. The next thing we're going to talk about is safely raising and supporting the vehicle so the suspension is hanging. So come right underneath here, this is where you're going to support the vehicle in the front. Now with the front of the vehicle safely raised and supported, we're going to remove all 5 of our 19-millimeter lug nuts. Remove your wheel. Now that the wheel is off, we have a nice clear view of our front strut. With that said, anything that you're going to be removing bolts or nut-wise, you want to of course, spray it down with some penetrant.
First, what I like to do is remove the sway bar link from the front strut. So I'm going to use some locking pliers, come from the backside right here and just try to hold onto the stud so it can't spin. All right. Let's get this off of here. Let's get the brake hose off of here. What we want to do here is just kind of move this brake line a little bit so we can give some slack between the stud and the strut, that way there we can lift this right up and out.
The next thing we need to do is loosen our 36-millimeter axle nut. The reason for that is because when this knuckle is going to want to pull away from the strut, we don't want to put a tug on any of our axle boots. A little bit of penetrant. The next thing you would want to do is either with a center punch, come right into that little dimple and just try to drive this axle into the bearing a little bit, just to give a little bit of slack, or of course, if you don't have a center punch, just put the nut so it matches up evenly, give it a couple loving bonks this way. That's nice and loose.
Next, we're going to remove our 18-millimeter nuts located right here and there. They hold the knuckle to the strut. Grab this bracket, carefully set it aside. These bolts right here are actually going to have to be forced out of the knuckle area. So what I always like to do is just take those nuts and I'm going to start them back on there, a few good threads, and you want to make sure that we're not going to damage the thread of the bolts. Give it a couple of loving bonks. Keep your ABS wire clear, do the same thing to the other one.
If you look at these bolts, you can see they're both the same, and if you look, you can also see that it's splined. That's the reason why it was stuck inside the knuckle.
Now we're going to carefully try to separate these two, but we want to make sure that this doesn't come down too far because once again, we don't want to put a tug on our axle boots, and we definitely don't want to put a tug on our brake line. If you want to have a bungee cord or something that's going to hold it at least away, but safely, that's up to you. There we are. I'm just going to set this right like that. Now we need to get under the hood. Now that we have the hood up, you have a clear view of the strut tower here. With that said, you don't want to touch this center nut. We're only going to remove these three, but when we remove all three, we want to leave one on there just a couple of threads for safety, and then we'll get under, we'll hold onto the strut and then we'll remove that nut.
If for some reason your strut didn't drop down when you removed all three of your nuts like that, it's because it's probably frozen along this area here into the strut tower. Use a little bit of penetrant and then carefully bonk right along here until it finally breaks free. Down like this, I'm just going to hold onto that strut, remove that last nut, and then I can remove it. There it is, friends. One thing that's always a great idea before you go ahead and try to put your new strut into the vehicle, is just line up the strut cap with the way the original was. So a match up from the bottom, make sure it's facing a straight line, and then just set these where they need to be. You can do that fairly easily by just holding the bottom and then turning the cap itself. Okay, friends, now it's going to be time to get our brand new front strut in here. As we do this, I like to mention that I always like to use a little bit of thread locker right on these studs. We'll call it your prerogative, but I recommend it. When we put this in, we want to make sure we line up the bolt holes with the studs coming out of our strut itself.
We'll start on all of our nuts, and then we'll snug them down and torque them to manufacturer specifications. Something that's important to make sure that I mention before we go ahead and put our knuckle up into the strut, is if you were to look along the backside of the knuckle, you might find that there's a lot of corrosion buildup. That's due to the fact that somebody made the knuckle out of aluminum and they put it in with the steel. When you have aluminum with steel, it just corrodes and that's what happens.
So feel along the back. If it feels as though it's raised, you need to make sure you take a chisel or whatever you might happen to have and clean that out. Now that I've got that knuckle cleaned up, let's go ahead and put this up so it's going to line up the bolt holes. Obviously, you want to clean up the threads on your mounting bolts. Something I always like to use is a little bit of red thread locker, we'll call it your prerogative. Go ahead and start those through from the front to the back. Grab your two mounting nuts and of course, your bracket for the ABS wire, start it on there. We'll start these nuts, we'll bottom them out, and then we'll torque them to manufacturer specifications.
Torque both these nuts to 89 foot-pounds. Let's get our brake hose back in there. It slides right into this little groove, and then of course we'll tighten it up. Let's get the sway bar link connected to the strut. Let's torque this to 48 foot-pounds. After you've bottomed out your axle nut, torque it to 159 foot-pounds. I like to put a bar straight across these studs like this, you want to be careful and make sure it's flat and not at an angle because you don't want to damage your threads on your studs.
We're going to go ahead and put the wheel on here. We'll start all the lug nuts, we'll snug them up and then we'll torque them to 100 foot-pounds. Torqued. Now it's going to be time to make sure we go ahead and torque these down. Before we do that though, you need to make sure you have your wheel on the ground with the weight of the vehicle. Let's torque them to 18 foot-pounds.
Tools used
Tools used
Tools used
Okay, friends. Before we get started, the first thing that I want to mention is you want to be safe. So, have hand protection and eye protection. The next thing we're going to talk about is safely raising and supporting the vehicle so the suspension is hanging. So, come right underneath here. This is where you're going to support the vehicle in the front. Now, with the front of the vehicle safely raised and supported, we're going to remove all five of our 19-millimeter lug nuts. Remove your wheel.
First, what I like to do is remove the sway bar link from the front strut. So, I'm going to use some locking pliers, come from the backside right here and just try to hold onto the stud so it can't spin. All right. Let's get this off of here. Okay. Now that we have the sway bar link off of here, we need to go over to the other side of the vehicle and remove the sway bar link from the strut as well. That way there, we can move the sway bar up and down as needed to get to that mounting nut. There it is, friends.
Okay, friends. Now it's going to be time to put it in our brand new front sway bar link. One thing I like to mention is it's always a great idea to do these as a pair. And if that's the case, now's the time to do it. So, let's go ahead and put this in starting with the bottom. Now, I'm going to use my 17-millimeter wrench to hold the stud from spinning, and then we'll snug it up. If you were to try to torque this you'd want to torque it to 48 foot-pounds. It's going to be very difficult to torque because as you try to twist, it's going to want to lift up on the bar. If you try to put the bar inside here, obviously, you're not gonna be able to get to it. So, 48 foot-pounds, if you can do it. Let's get the sway bar link connected to the strut. Let's torque this to 48 foot-pounds. We're going to go ahead and put the wheel on here. We'll start all the lug nuts, we'll snug them up and then we'll torque them to 100 foot-pounds. Torqued.
Tools used
Tools used
Tools used
