Replaces
This part doesn’t fit a . Select from parts that fit.
Light Assembly Lifetime Warranty
Frequently bought together
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
The bulbs are for testing and not covered under our warranty. Our warranty applies to the light assembly only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to service the bulbs, as well as replace the entire parking light assembly on this 2002 Chevy Suburban. It's the same part and similar process on these Suburbans from 2000 to 2006. We show you on the passenger's side, but the driver's side is a similar procedure. The items you'll need for this includes new parking lights from 1AAuto.com, a flat blade screwdriver, a Phillips screwdriver, and a 10mm socket and ratchet.
Start off by removing your headlight. To do that, you just push these rods in, and then lift them up and out. Now you can pull your headlight out. Just reach down behind it, and you can see there's a tab right here on the parking light, just push that in, and your parking light will pop out.
To service the bulbs, you just push the tabs on the socket and turn it. It's counterclockwise to remove it. The bulb pulls straight out. You can push your new bulb in and twist it back into place clockwise to lock it. This middle one is the same, and the one on the end, just pulls straight out, bulb pulls out, new one goes in.
Now, to replace the entire assembly, remove all three of your sockets from the light. On the bottom is the old parking light; above it is the identical match from 1AAuto.com and above that is a performance version we offer. Both parking lights will fit exactly the same as the stock parking light.
Now twist your sockets into your new parking light assembly and push this last one in. Then push this tab in first into this slot right here, and then just push the parking light straight back into place. Line up your headlight and push it back into place. Then push those rods back down in, turn them back inwards to lock them, and you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
All right. There's these little retainers right here. Slide this out, and slide these straight up. You can grab the light assembly. It slides straight forward. Disconnect the connector right here. There's two tabs. Just slide up on the two tabs, and then the connector comes out, and same with this one. And there's a release clip right there. Just take a long screwdriver, push that down. As you push that down just slide out on the light. And you can push down on these tabs right here, and twist it. Twist the socket counterclockwise, just like that. And this last one, just twists counterclockwise.
And take the light assembly, and put the sockets in, and twist them to the right. Just line it up. And twist it to the right. There we go. And you might have to push the wires back in. You want to slide the front of it in first, and line the clip up, and lock it in place. And you can line it up with the plugs. Connect the bulb, and connect the high beam bulb, and just line this up. And take the pins. Get both pins started first. All right. Push the pins, lock them in place.
Tools used
