Install Tip: Keep & reuse your original hardware, new hardware is not included with this item.
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Hood Latch 2000-06 Chevy Silverado
How to Replace Hood Latch 1999-2007 Chevy Silverado
Created on:
Tools used
Socket Extensions
Flat Blade Screwdriver
Rust Penetrant
10mm Socket
Ratchet
1. Removing the Hood Latch
Remove the 10mm bolts from the hood hinge
Pop the clips out of the radiator cover
Remove the cover
Remove the hood hinge
Release the cable from the hinge
Remove the cable from the latch
2. Installing the Hood Latch
Attach the cable to the hood latch
Lower the latch to the radiator support
Tighten the 10mm bolts to the latch
Test the latch
Press on the plastic cover
Push the clips into the cover
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
Replace the hood hinge. Remove the 10 millimeter bolts that are holding it. There's one on this side and two on this side. I'm going to start with the single one over here, loosening it with a 10 millimeter socket. I'm going to loosen this one. Loosen the bottom one. I'm going to switch to a ratcheting wrench to make it a little bit easier. Once I get this one loose, pull it out with my fingers and put it aside.
Work on this one here. Rather than struggle to try to get to these bolts, I'm going to pop these clips out with a flat bladed screwdriver. There's a bunch of push clips all around here, we can take this trim right off then we'll have access to hood hinge. Much more space without this in here. Get my fingers in here, remove this one. Lift the latch out.
To unclip it from the hood release cable so I can actually push this cable out, around and I can unclip it from here. I'm just going to push it in with my thumb. Get these bolts out of the way. Put that cable there. The hood latch is removed.
Here's the old hood latch from our vehicle and the new hood latch from 1AAuto.com. It’s similar in design with the same bolt holes. There's these square holes so that the hood latch can be adjusted. Same mounting point for the hood release cable as the original. This should fit in the truck and work great for you.
I reattached the hood release cable. Go through here, and actually what I'm going to do is loop it over here first, pull it back, and push it through. I can put it back on the radiator support. You can see where the original one was. Some marks here so in order to get it close to adjustment, so I'm going to put it where the original one was for now. If we need to adjust it afterwards, you can leave these bolts loose and move it side to side and up and down to adjust as necessary.
But for now, I'm going to line it up where the original one was. Reinstall the bolts. Start tightening these, get it to line up close to the original one. I'm just going to tighten this til I feel it get tight, and then I'm going to stop. Bring the final bolt in. It wants to go by hand.
Our hood latch is replaced. It did come pre-greased but now's not a bad time to add a little more lubricant to it. Looks like the adjustment is good so we're going to leave that as is. Make sure the release works. The hood latch is replaced. Final step is just reinstalling the plastic cover, goes over the grille. Just push all the clips back into place. Push them down and lock them. If the center part has come out, that's okay, we'll reinstall it.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
Socket Extensions
10mm Wrench
10mm Socket
Ratchet
Needle nose pliers
Okay, friends, so one of the first things we need to do to start this hood latch repair is we're going to come right here to these three 10-millimeter headed bolts. You'll see two on the driver side and one over on the passenger side. Remove all three. There we are. Do the same to the rest. And if you don't feel like using a wrench, use a 10-millimeter socket with an extension.
Come right through the grille, go ahead and remove it. Okay. There it is. Hold onto this because there's nothing else holding it on. The next thing we need to do is get the release cable off of here. If you squeeze those two ears, you should be able to get it off. Okay. Just draw that out. Bring it down through the slot. Then take this. Bring it right up and out of there.
There it is, friends. Now, it's time to get our nice new latch in there. We're going to install it in the reverse process. So, just take that cable, put it around the backside there, pull it through. Now, I'm gonna go ahead and give it a tug. And I'm going to slide those ears through. Make sure they lock in completely.
Bring this down. Start in all your screws before you tighten any of them down. Okay. Those are close enough. This can still move around. So, next, we need to take a look at our old latch. If you look, you should be able to see some circles where the old washers for the bolts used to be. You're going to want those markings to be in approximately the same place on the new latch.
That's going to be a great starting point. If I was to tighten this up in a completely up position where my old one was in the completely down position, more than likely my hood's not going to be aligned properly and it might not even open. So, I'll just start it where the old one was, and we'll go from there. All right. Let's give it a quick test. Give it a nice tug. Make sure it doesn't move around too much up or down. That feels good. Our next test is to go pop the hood and hopefully, it breaks free and opens up.
So, that's what we were looking for right there. We wanted to make sure that this latch is going to be working properly right from the get-go. If for some reason the hood came down but it didn't latch in, you need to fix your adjustment. Maybe the hood came down and it did latch in, but you noticed you had to push down on the hood to get it to completely unlatch, once again, you need to complete your adjustment. Once you get it just right, we're going to continue on by snugging these up completely.
Okay. Close the hood, take it for a road test.
BDA49281
In Stock
Product Reviews
Loading reviews
4.25/ 5.04
4 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
2
1
1
0
0
Top notch
J
August 7, 2018
With cheap price you might be a little weary about 1AAuto, this is my second purchase from them, my first was a window track which hasnt failed me in over a year. My second being this hood latch, I compared it to my old one and its 100% the same. Bolt right in and replaced my old worn old one, now my hood doesnt have the shakes. For $30 the will and have my business.
D
May 12, 2020
so far it's okay
Worked perfect
Lee
December 18, 2020
Great replacement product. I tried the dorman one from a box auto parts store and the latch handle was bent in a different direction from stock so it didn't work. I ordered this one and it was identical to factory. I should have bought from 1a from the beginning and I would have been done sooner. Don't make the same mistake I did.
Fit perfect
Jack
April 14, 2023
It fits perfectly and works great. My only reason for not giving it 5 stars is that I just put in on and do not know the longevity.
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Chevrolet is a registered trademark of General Motors Company. 1A Auto is not affiliated with or sponsored by Chevrolet or General Motors Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.