Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Created on:
Tools used
Remove this cover. I'm gonna use an 8 mm socket. Loosen that bolt up, and slide the cover up. And loosen up this worm clamp. You can use an 8 mm socket or a straight blade screwdriver. And the same with this one, right here.
Use a trim tool, and just separate this retainer right there, with that bracket, and slide the snorkel off there, and pull it up. Just to gain more access, I'm gonna pull this air box off, disconnect the mass airflow sensor, grab the air box, pull it straight up, and you could slide it out. There's two tabs, and this holds it in.
Now, when we go to take the reservoir off, you don't necessarily need to drain the entire coolant system. If you wanted to drain it a little bit so that the coolant just drained down to that position, you could. Or if you just take this hose off, just be aware that a lot of coolant is gonna drain out there. And just, again, do this while the vehicle is cool. Don't do this while the vehicle is hot.
I'm gonna take the bottom radiator hose off. I need to drain the coolant. There's no coolant drain on this radiator. So I'm gonna use a hose clamp and pliers, that have the cable style to remove that hose clamp. Make sure you have the drain bucket underneath.
Just let that drain out. Now, you can use some hose clamp pliers. Move this hose clamp just down the hose a little bit, and just twist the hose back and forth. If you have to, you can use a right-angle pick to just get underneath and then just work it off. There we go. And the same with this top hose. Remove the clamp. And twist the hose off. And remove this bolt. Use a 10 mm socket. And there's a nut right here. Use the same 10 mm socket. This one's pretty rusty. I'm gonna spray some rust penetrant on there.
And just slide this up. It's clicked in, in the back, right here. And you can disconnect this connector right here, down on the connector, and slide it off. And now, we want to plug this connector in, just like that. And line the clips up in the back, over near the side. Looks good. Then take the nut, install that back here, and then the bolt goes in right here, and tighten them down. Install the lower hose, and use the hose clamp tool. I'm gonna do the same to the top hose.
All right. Now, we attach the lower radiator hose. Should be all the way on there. Release on the clamp, just make sure it's tight. Looks good. And slide the air box back in position. What we want to do is slide this piece. It's gonna go right here. It's gonna slide there, and then push the two push pins straight down.
Push down. It's good to go. Reconnect the mass airflow sensor, and put the snorkel back on. Line this up with the throttle body and the air box, and tighten up the worm clamps, and line this bracket back up. Put the cover on, slide it in the back, get the bolts started, snug it down.
Now, if you just replaced the reservoir and you didn't lose that much coolant, you can top off the reservoir. You're still gonna want to run the vehicle for about ten minutes, monitoring the coolant level and adjust accordingly and then after it cools down, adjust it again.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the radiator overflow bottle on this 2002 Chevy Suburban. It's the same part and similar process on these Suburbans from 2000 to 2004. The items you'll need are a new radiator overflow bottle from 1AAuto.com, flat blade screwdriver, 10mm socket and ratchet, pliers, two pairs of locking pliers, and a drip pan.
Start off by loosening up this hose clamp. Then, just pull this hose free from the air box. Lift up the air box and just push it towards the engine to free it from the side. Then, lift up that hose and lift your air box up and out.
Clamp on to this hose with locking pliers and make sure you have a drip pan below it. Then just push these teeth together on the hose clamp and pull the hose free. Then remove these two 10mm nuts. We'll just fast forward as Don does that. Now, push the teeth together on this hose clamp. Slide it down the hose. Then clamp onto this hose with locking pliers and pull the hose free. It's a good idea to tip the tank back so it makes less of a mess. Then just pry that hose off with a flat blade screw driver until you can get a good enough grip on it, and pull it off. Just lift up on the tab on this harness and pull it free. And your radiator overflow bottle is disconnected.
On the left, is the old radiator overflow bottle. On the right, is the new one from 1A Auto. You can see they're identical, and they'll fit exactly the same. Take your new overflow bottle and reconnect the harness. Then, push that lower hose into place. Now push this tab into this slot. Push the bottle down. Then remove those locking pliers and slide that hose clamp back into place. We'll just fast forward as Don replaces those two 10mm nuts and tightens them up. Now push the teeth together on this hose clamp again and push the hose back into place. Then just remove the locking pliers.
You want to push these three tabs down into these three holes. Pull back the air hose and push the back end of the air box down in first. Then just push the box straight down into place and make sure you push those tabs in, push the hose back onto the front, and then tighten up that hose clamp.
Obviously you'll want to refill your radiator fluid. There are cold and warm fill lines. Obviously our engine's cold right now, so fill up to the cold line. You should after you refill it, the first few times you drive your vehicle just check it and make sure that it's at the proper level.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet.
Hi I'm Mike from 1A Auto. I hope this how to video helps you out and next time you need parts for your vehicle think of 1AAuto.com. Thanks.
In this video we're going to show you how to replace the radiator overflow bottle in this 2002 GMC Sierra 2500 HD. It's pretty much the same procedure in most GM trucks, SUVs and pickups between the years of 1999 and 2006. The items that you'll need are a new radiator overflow bottle from 1A Auto; a flat blade screwdriver, pliers, vice grips, a funnel, a bottle or pan for the coolant and a 10 mm socket and ratchet.
To start off we're going to remove the air intake box. You just want to use a flat blade screwdriver to loosen up that bolt and that will loosen the clip and you can pull the air intake hose off. Then you just want to pull back on the air intake box and pull it up and out. You want to use pliers to pinch that clip together and then you want to pull that hose off. It helps if you loosen the cap. It releases some of the pressure and then the hose should pull right off. Next what you want to do is remove the 10mm bolt from the front of the overflow bottle and the 10mm nut from the back of the overflow bottle. We'll just fast forward while he does that.
Now you want to lift the bottle up and out and disconnect the connector there by pulling back on the tab. Now you want to tilt the overflow bottle back and clamp the hose with a pair of vice grips. Now you want to use a pair of pliers and push that clip together and slide the clip back off of the radiator bottle. Then you want to pry off that hose using a flat blade screwdriver. Once the hose is off you can remove your radiator overflow bottle from the engine. You want to dump the coolant into a bottle. Use a funnel or you could also use a pan and then you could pour it right into the catch pan. You need something to store the coolant in. You want it to be relatively clean because we are going to pour this back into the radiator overflow bottle.
You can see the old radiator overflow bottle on the right and the new one from 1A Auto on the left. They're exactly the same; same mounting brackets. You want to tuck your new radiator overflow bottle down into the engine. Reconnect that hose and you can disconnect your vice grip. Then you want to use a pair of pliers to slide that clip back onto the overflow bottle. Now you want to connect your clip and line up the overflow bottle. We'll fast forward here as he replaces the 10mm bolt and the 10mm nut that secure the overflow bottle.
Now you want to reconnect that top hose. Using pliers push the clip back together and it should release it. Now you want to pour the radiator coolant back into the overflow bottle. Replace the cap. Now you want to put your air intake box back in so just pull back that air intake hose. Put the back end of the air intake box in first and push it down into place. What you want to do is you want to line up the two clips on the bottom of the air intake box with the two holes in the body of the truck. Then you want to reconnect that air intake hose. Push the box down into those holes. Then using a flat blade screwdriver tighten up the screw on that clip and then you're all set.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free 888-844-3393. We're the company that's here for you on the internet and in person.
