Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Part Details
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
Created on:
Tools used
All right, friends. So, it's time to get started on doing your spark plug wires. Before you get started on that though, we always like to make sure that you have safety as your number one concern. Eye protection and hand protection at all times. Aside from that, let's get into it.
We're gonna start right over here on the passenger side front of the engine. We're gonna show you how to do one spark plug wire. They're all the exact same procedure. So, I don't necessarily need to make you stay here very long and watch. Grab this right down here. You definitely wanna make sure that your engine is not hot in any way. This area right along here is called your exhaust manifold, and if your engine has been running, it's gonna be very hot. Assuming your engine's cold, we'll come right here. Give this a nice twist. If it doesn't break free, you can use something like pliers or pretty much whatever you want because, well, the wire's garbage anyway. Grab onto it, twist, and pull. It should pretty much come right off of there. Now we'll come right up here. We're gonna do the same thing. Twist it to break it free. Pull it down. There it is.
Okay. So, we've got our new spark plug wire here. Something to pay attention to is our old wire had a nice shield on here for the exhaust. Our new wire does as well. Before we go ahead and start this, we wanna take a little bit of dielectric grease, it doesn't have to be very much, go right along inside this area here where it connects under the spark plug. Take some more, go right along this area right here. The reason for doing this, it's gonna make it so it's much easier to take off down the line, and it's also gonna prevent moisture from getting inside there. At this point, we're gonna let the bottom side dangle and we'll put the top side onto the coil. Press it up on there. Listen for a click. There it is. Give it a nice twist. Give it a little tug. Make sure it doesn't just fall right off of there. We're gonna grab the bottom side, slide it carefully onto that spark plug. Make sure you're going straight on and you're not trying to force the spark plug in any direction it doesn't want to go, because it is made of porcelain and it can break. Force this on. Listen for the click. Give it a wiggle. Give it a tug. Do the same down the line to all the rest.
Tools used
All right. We want to disconnect the battery. Disconnect the negative cable, use an 8-millimeter ratchet wrench or a wrench, and slide that out of the way. All right. Now, replace the plug wire. Just grab the top of the wire, pull it down. And then, at the spark plug, you can try twisting this first. See if you can loosen it up. Try to pull it. Try not to bend the aluminum too much, but if you're struggling to get it off, you might have to a little bit. There you go. Pulled that one out.
You can take a little dielectric grease or some silicone lubricant. Just put this in the end right here. Then, you want to take the heat shield off the old wire and reuse this. Now, we can line this up, up top on the coil. And then line it up with the plug. Slide it in position. Make sure it clicks in place, just like that. Then you're going to do the same procedure for the other wires.
Now, we can hook up the battery. Line it up, get it started, and snug it up. Just make sure it's not loose. That's good.
Tools used
You can move these heater hoses out of the way, just pull them out of the bracket and slide them to the side. Disconnect the wire at the plug. You can give it a twist and pull it off. Disconnect the wire at the coil, do the same. Twist it. Slide it right off.
Take the new one. This new one has a little bit of dielectric grease in it. But if it doesn't, you can always add some. Slide the part on into the coil, lock it in place. And then put the other part for the spark plug and lock it down. And you can do the same with the other ones. And move these heater hoses, put them back in the bracket.
