Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Part Details
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Highest Quality MaterialsMade from highest quality materials that meet or exceed OEM standards
Quality Tested - built to a strict level of product standards.
Item Condition:
New
Attention California Customers:
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
So, I took out the glovebox just so you can have a better view, but you don't necessarily need to. You can see the blower motor right here, you've got your electrical connector. Go ahead and push up on this tab and then draw the wire out of there. After that, just press on these tabs on this and this should work them out. There it is. This one, same thing. Pop it right out of the way. At this point, you're going to look for your mounting screws. There's one right here, there's one back there, and one over on the side 7/32s. Let's pull this down. Oh. All right. Let's get this blower motor up in here, start in any of the screws that you can, and then we'll bottom them out once we get them all started. Just make sure you snug them all up. Now, we're going to plug in the blower motor. I'm gonna get that right in there. I'm sure you get your wire situated. Let's test it. Definitely sounds like it's working perfect.
Tools used
So, I took out the glove box just so you can have a better view, but you don't necessarily need to. Can see the blower motor right here. You've got your electrical connector. Go ahead and push up on this tab and then draw the wire out of there. Hopefully. After that, just press on these tabs on this and this should wanna come out. There it is. This one, same thing. Use the 7/32 bit. This one is a little bit harder to get to. ok. Let's get our new resistor up in here. Make sure you've got the gasket on there. Should be attached but gonna start in my mounting bolts, once they're both started, I'll snug them up. Awesome.
So, I just pulled this up through the glove box area. I wanted to show you, you can see where it's kind of burnt a little bit here on the connector, that's very common. If you're replacing your resistor, more than likely you're going to see that. That's why TRQ was kind enough to give you a brand new resistor harness here. So, I'm going to show you how to wire it in. Now, we're just gonna look at these wires. If you see one that's burnt like we have, just make sure that the wire isn't damaged, if it is, of course, you need to cut higher than that. Now, what I'm going to do is I'm going to start cutting these, gonna go just like this. And then I'm going to come up just a little bit higher, and then a little bit higher than that, and then a little bit higher than that. That way there these are all in a step position, and when I go to put these on to the new, they're not all going to be directly in line with each other and making a big old ball. Let's go ahead and take off the outer sheathing on these. All right. So, we got all the sheathing off of there. This looks good. Let's use these. You can see right through where the metal is right there, you need to make sure you get the metal part of the wires up to there, and then crimp it down. Go ahead and twist up your wire. Slide this right over so you can see the metal going inside the metal housing of the connector, and then go ahead and crimp it down. Give it a nice tug. Perfect. Do the same to all.
So, now, we're going to trim this down to a working level because obviously, we don't need this much. Okay. Now, if we take our old connector and our new connector, you can match them up, make sure you have your flippy-do in the same area. That's super important. If it's upside down, it's going to cause a major issue. Once you have it like this, just line up your first wire with that one, this is the one we're going to splice. And then after that, we're going to move along to doing the others. Give it a little twist. Go ahead and put that in there. Hopefully. Push it right in. Crimp it down. Awesome. So, now, we're just gonna stretch this out and then lead this up to the next shortest. We'll trim it as needed, and then we'll continue on just like that. These look great.
Now, we're just going to carefully heat these up and they're going to shrink down.
Do the same to all. Now, we're going to plug in the blower motor. I'm gonna put that right in there. Make sure you get your wire situated. Go ahead and plug in the resistor right over there. And then, of course, get this wire situated as well. If you have any extra, you can, of course, put it behind the carpet and then just make sure you have it secured. That looks great. Okay. All that's left is testing it out. Make sure it works on all speeds. Let's test it. Definitely sounds like it's working perfect.
