WARNING: This product can expose you to chemicals including 1,3-Butadiene, which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Air Intake Hose 1995-97 Pontiac Sunfire
Created on:
Tools used
Flat Blade Screwdriver
1. Removing the Air Intake Hose
Disconnect the wiring harness from the semsor
Pull the cable out of its clip
Use a flat blade screwdriver to loosen the hose clamps
Twist the intake hose off at both ends
Pull the intake hose out
2. Preparing the New Air Intake Hose
Transfer the hose clamps from the old intake hose to the new one
Transfer the cable clip from the old intake hose to the new one
Transfer the sensor from the old intake hose to the new one
3. Installing the New Air Intake Hose
Push the intake hose onto the PVC valve
Push the hose onto the throttle body
Push the hose onto the air filter box
Tighten the hose clamps
Push the cable into its clip
Connect the sensor wiring harness
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing or maintaining your vehicle. I'm going to use my 20-plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly: that's going to save you time and money. Thank you and enjoy the video.
In this video, we'll be showing you how to replace the intake hose on this 1997 Pontiac Sunfire, same as any '95 to '97 Sunfire or Cavalier with a 2.2 liter and probably similar to most of those J-body cars from 95 to 05.
You want to replace your area take hose. Sometimes these can dry out, they can crack and/or during a repair or something, they can get broken. It's very important because it's the link between your throttle body and your air filter. You don't want dirty or foreign contaminants getting in there because that will ruin your air flow sensor and then you'll have a more expensive repair. It's fairly easy and I'll show you there's a connection back here that you need to undo. Just pull up with your thumb, and it comes off. For this, you can move it to the side or undo it. Pull that cable up and out. Then you're just going to need a regular screwdriver loosen up the clamps. You twist this a little bit and pull it off of there. Do the same thing over here. Loosen your clamp. Shake your clamp. Twist to pull the hose sone. That's probably because the PVC valve's here too. Then your hose is off.
Here's the original and here's the replacement from 1A Auto. You do need to transfer some of the parts, your clamps, this clip for the cable and this sensor, only to go into the new hose, but the hose is made just like the original. You have the provision for the PVC and everything, so if you've got a dry, cracked or broken hose, the new hose from 1A Auto, is going to hold up just like the original and fix the problem. For this car, this original is still in good shape so I'm going to re-install it. This is just a test case for the video.
Before we install, we're going to put it underneath the cable here and we're going to kind of push it on to the PVC here while we're working it, also under the throttle body. Kind of do those at the same time and you can see where it was on the throttle body, so you want to make sure you get all the way back on. It looks like the bottom is on. The top's having a little trouble. Maybe our clamp's not loose enough. There it goes, nice and easy. We're on there and now we'll work it right back on here. We'll tighten these up. We want to make these nice and tight. Actually you can really see here, a mark where the clamp was, and how tight it was. At least get back to there, which is pretty tight. Tighten this up. Put our cable back in and plug in our sensor.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
696-101
In Stock
Product Reviews
Loading reviews
There are no reviews for this item.
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Chevrolet is a registered trademark of General Motors Company. 1A Auto is not affiliated with or sponsored by Chevrolet or General Motors Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.