Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Direct Fit - No vehicle or wiring modification necessary
DOT, SAE, and FMVSS Compliant - Meets on-road use regulations
Matching set for a restored look
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
How to Replace Headlight 2008-15 Nissan Titan
How to Replace Tail Light 2004-2015 Nissan Titan
How to Replace Tail Light 2004-15 Nissan Titan
Created on:
Tools used
Socket Extensions
Flat Blade Screwdriver
8mm Socket
10mm Socket
Ratchet
Needle nose pliers
1. Removing the Grille
Twist off the clips from the grille with a flat blade screwdriver
Pry out the clips on both sides
Remove the clips from the bottom of the grille
Pull out on both sides of the grille
Release the harness and pull out the grille
2. Removing the Headlight Assembly
Remove two Phillips screws underneath the fender
Pull back the panel and remove two 10mm bolts
Remove two 8mm bolts at the top of the headlight
Disconnect the harness and pull the headlight up and out
3. Servicing the Headlight Assembly
Lift up the tab on the harness and pull it free
Twist the socket counterclockwise to remove the bulb
Twist the socket clockwise to lock the new bulb
Reconnect the harness
Push the clips to the side with a flat blade screwdriver and pull the bracket off
Remove the clips on the bracket with pliers
4. Reinstalling the Headlight Assembly
Push the clips into the bracket and clip the bracket to the new headlight
Line up the pins on the panel and push it directly to the back into place
Reconnect the headlight harness
Put the washers back into place beneath the headlight
Tighten the 8mm bolts
Tighten the 10mm bolts underneath the fender
Push the panel into place underneath the fender and replace the two Phillips screws
5. Reinstalling the Grille
Pull the clips out by pushing the tabs on the top and bottom
Slide them into place on the grille
Line up the clips and push the grille back into place
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to-video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to service as well as replace the entire headlight assembly on this 2009 Nissan Titan. We show you the passenger's side, but the driver's side has a similar procedure. The items you'll need for this are new headlights from 1AAuto.com, a flat blade screw driver, an 8mm and 10mm socket and ratchet, and a pair of pliers.
Along the top of your grill you'll see these four clips. Using a flat blade screw driver, just twist them and repeat this process with the other three. Now there are two clips, one on either side, right here. Just pry it out and do the same thing over here. Now, along the bottom of your grill you'll see two more of those twisting clips. We'll just fast forward as Don does that real quick. Pull out on the side of your grill and do the same thing on the other side. Pull this harness free, and your grill's free. Now, you want to remove a Phillip's screw right here and right here. We'll fast forward as Don does that. Pull back that panel and inside here you'll see one 10mm bolt right here, and you have to access it from right over here. There's another 10mm bolt right here. We'll just fast forward as Don removes both of those. Now, at the top of your headlight, there's an 8mm bolt here and an 8mm bolt here. We'll fast forward as Don removes those. Disconnect this harness by pushing on the tab and pulling it free. Then pull out from this side of the headlight, and now you can lift it up and out.
To service the bulbs, lift up the tab on the harness and pull it free. Twist the socket counterclockwise and the bulb pulls out. Twist it back in clockwise to lock it and reconnect your harness. This bulb right here has a similar procedure. It just pulls out. Push the new one in and twist it back. These bulbs are little bit different. You twist it counterclockwise, pull it out, and the bulb pulls free from the socket. Then you push your new bulb in. Then twist the socket back into place, turn it clockwise to lock it, and the small bulb next to it has the same procedure.
Next, you want to separate this bracket from the light. Just pry the clips to the side and the bracket will pull off. If you damage it, we sell replacements of these at 1AAuto.com and they will fit exactly the same. They aren't painted to match, so you'll have to go to a paints department and get a matching can of paint and just paint it. You want to remove these clips by just twisting them and then pushing the tabs on either side with some pliers and pulling them free.
On the left is the old headlight; on the right is the new one from 1A Auto. You can see they're identical. They're going to fit exactly the same. Push your clips into the bracket, then clip that bracket panel onto your headlight. Now, line up the pin and panel and push it back into place. Your headlight has to be at the angle that you're going to push it directly back for it to snap in. Then you want to reconnect your headlight harness. You would have seen these washers when you pulled your headlight off. Push them back into place underneath the headlight. It separates the headlight from the car. Do the same thing right here. Push the bolt through and just tighten it up. We'll fast forward as Don tightens those bolts the rest of the way and then replaces those two 10mm bolts underneath.
Push that panel back into place tucking it up and into the fender. Then replace those two Phillips screws. Now, pull these clips out and just push the tabs on the top and bottom and they pull right out. Now slide them into place on your grill. We'll fast forward as Don does this with the rest of the clips. Line up the clips, and then just push the clips back into place. You're all set.
We hope this video helps you out, brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Socket Extensions
Socket Driver
Straight Cutters
Wire Ties
Ratchet
Trim Tool Set
Tools used
10mm Socket
Ratchet
Needle nose pliers
1. Removing the Tail Light
Remove the 10mm bolts from the tail light bracket
2. Servicing the Bulbs
Twist the bulb socket counterclockwise out of the light
Pull the bulb off of the socket
Push on the new bulb
Twist the bulb clockwise into the light
3. Removing the Tail Light Harness
Disconnect the tail light wiring harness from the truck
Disconnect the tail light wiring harness
Remove the gasket
Pull the tail light and the wiring harness out
4. Installing the New Tail Light
If the new tail light has clips remove the old clips from the truck with pliers
Line up the bolt holes on the headlight bracket to the bolt holes on the vehicle
Replace the 10mm bolts into the tail light bracket
Reconnect the tail light wiring harness
Re-clip the wiring harness to the truck
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to service the taillight as well as replace the entire assembly on this 2009 Nissan Titan. We show you on the passenger side, but the driver side is a similar procedure. The items you'll need for this include new tail lights from 1AAuto.com, a 10mm socket and ratchet, and a pair of pliers.
Start it off by removing these two 10mm bolts right here, and we'll just fast-forward as Don does this. If you're just looking to service your bulbs, just pull the tail light out, and the socket is twisted out counterclockwise. Pull the bulb out, push your new one in, and twist the socket back in clockwise to lock it. These two are exactly the same so you can twist them out. Pull the bulb free. Push your new one in and twist it back into place.
If you're looking to replace the entire tail light assembly, just come down here underneath your truck. Pull the harness free from the truck, then push the tab, and disconnect it. Then put the harness up and over here, and then just pull the tail light assembly out. Pull this gasket free, and then pull the harness up and out.
On the left is the old taillight; on the right is the new one from 1A Auto. You can see they're identical, and they're going to mount exactly the same. If your new tail light comes with clips, just remove these old ones using a pair of pliers. Then, feed the harness of your new light back down into the truck, and push that gasket back into place. Now, push your taillight back into place making sure that those clips on the side line up, and then just hit them into place. We'll fast-forward as Don replaces those two 10mm bolts. Now, put the harness back up and over here, reconnect it, and then re-clip it to the truck. You're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Product Reviews
Loading reviews
There are no reviews for this item.
Customer Q&A
Do these include the bulbs please?July 10, 2023
Stephen H
10
New light bulbs are not included with this assembly. Occasionally, manufacturers leave test bulbs in the lights. If you receive test bulbs, you'll want to replace them with your original bulbs or with new bulbs.
July 12, 2023
Emma F
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Nissan is a registered trademark of Nissan Motor Co., Ltd. 1A Auto is not affiliated with or sponsored by Nissan or Nissan Motor Co., Ltd.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.