Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Part Details
Our control arms are designed to be direct replacements for the original factory parts. They are 100% brand new and require no modifications for installation. No special tools are required because all of the bushings come pre-installed.
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Hi. I'm Mike from 1AAuto. We've been selling auto parts for over 30 years!
Use a large pry bar or a flat-bladed screwdriver to remove the wheel cover. Just kind of slide it between the wheel and the plastic and pop it off. These lug nuts are a 21mm socket. I’m going to use that and a breaker bar to loosen them while the vehicle's on the ground. Raise and support the vehicle. We're using a two post lift, but you can use a jack and jack stands. The lug nuts are loose, so you can take the socket and finish removing them. I’m just going to hold onto the wheel. When I take the last lug nut off it's going to be loose. I don't want to drop it. If you drop the lug nut that's okay; you just don't want the wheel to fall.
The ball joint is bolted to the lower control arm and has two nuts and studs and one single bolt, and of course the ball joint goes through the knuckle. We're going to spray some rust penetrant on here before we try to remove these. While this is mostly together, I just want to loosen these three 17mm – well, there are two 17mm nuts and one 17mm bolt. I’m going to use a 17mm socket and a large breaker bar to get these free.
Now I want to remove this cotter pin that's up here. So we take some needle nose pliers, bend it up, get them straight, and wiggle it back and forth, push it back out of the castle nut. Then take some side cutters, and I think what I'm going to do is just cut these off because they're real, real rusty. I’ll fold them as flat as I can and push them together. Take a punch and a hammer. The punch typically fits through the ball joint hole once it's opened up. And just do my best to pop that back out the other way.
This is 19mm. I'm going to put the box wrench on here and try to just break whatever's left of the cotter pin by turning the nut off. It's pretty stiff so I'm going to hit it with a mallet. Put some more rust penetrant on there. Just keep turning it off. Normally you'd try to pull that cotter pin out, but it was so rusty we had to break it. Then you’ve got to be careful you don't get the box wrench part of there stuck in here. I'm going to turn this on just a few turns. Just work it down and then I can slide the box wrench out. Because now I've got it free, I'm going to switch to the open end, and luckily the ball joint is stuck in the taper of the knuckle so it's not spinning as I'm trying to remove it. If the ball joint started to turn inside of the knuckle into the taper, it was just turning with the nut, you can try to put a floor jack up in here and put pressure onto the ball joint to try to hold it tight, and that's really about all the options you have.
Use the open end. So if this happens, and the CV axle is in the way, you don't have to take the CV axle out. I'm going to thread this back down because I know it'll come free. Get back down until just enough room there. If you don't have a ball joint removal tool or a separator tool, you can use a metal sledge hammer, a small one. You want to hit right here on the knuckle. Be very careful because you can break the knuckle this way, but you can give it a couple good strong whacks. Yeah. See, I don't like doing that because you have to hit it really, really hard, and I'm always worried that we're going to break a knuckle that way. So, since I've got a ball joint separating tool, I'm going to use that instead.
I think it's going to be easier for me to get in here if I remove these fully. Just pull this control arm down. Pull that down out of the way. It gives me a lot more space to work. So I'm having trouble getting the ball joint tool in here because it's super tight, and doesn't want to fit. The nut can't quite come off because the axle is in the way. I've put a couple little dents in the knuckle from trying to hit it with the mallet, so I don't want to keep doing that. I've kind of decided that if I took a pry bar and just very carefully pry it against the CV axle and pry it down, I could actually get it to pop out of the knuckle. It's not the most ideal method, but it worked. The ball joint will just come right out of here. If the shield is in the way, that's fine. Just put our pry bar in here, just pry the dust shield back, and pull the ball joint out.
Here's the old ball joint from our vehicle. You can see where the cotter pin broke off. It's still inside the little cotter pin hole. Here's a brand new one from 1AAuto.com, the same exact style. It comes with two new locking nuts for the studs, and a new bolt to go underneath. It also comes with a new castle nut, and a brand new cotter pin. This should fit right in and work great in your vehicle.
I’ve just got to wipe down all the extra grease that squeezed out of the old ball joint while I was trying to remove it, and slide our new ball joint up into place. You just need to pry the dust shield back a little bit. It's going to be squished right up in there. Get the nut caught.
Put this down and under. Just catch these two lower lock nuts so it doesn't pop out. Pull this down so it's flush and install the bolt.
We'll take a 19mm wrench, tighten this down. I’m going to switch to the longer wrench. You just want to make this nice and tight as possible. That feels pretty tight. I also want to make sure -- a we'll go a quarter turn more just to line up the hole with the castle nut. Take some pliers, bend this one up and over. Cotter pin is locked in there, it's not going to come out.
Snug down the 17mm bolt. Nuts on the replacement ball joint are 19mm. Snug these down. They have a nylon locking portion to them. Torque these lower nuts and this bolt to 55 foot-pounds. These are the 19s. Switch sockets. The ball joint is replaced.
Reinstall our wheel. It's important to note, these lug nuts have a taper. The taper meets the wheel, matches the inside of the wheel. Don't install them with the flat side like this; that is incorrect. Install them with the taper to the wheel. It helps locate the wheel on the lug nut side. I'm just using the socket and ratchet to bring these down snug before I put the car on the ground. Torque the lug nuts to 76 foot-pounds, going in a cross pattern.
Reinstall the hub cap. You're going to line up the opening for the valve stem with the valve stem on the wheel. Just push it in place.
Before we start the car, just going to gently press the brake pedal down; not all the way to the floor, maybe about a quarter of the way, and just pump it. This will bring the brake caliper piston out to meet the pads because we compressed it, and you'll start to feel it get more solid as it pumps up
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
Okay, friends. One of the first things we need to do is safely raise and support the vehicle with the suspension hanging. Once we've done that, we're gonna remove our five 21-millimeter lug nuts. Let's get the wheel off of here. Now that the wheel's off, we have a nice, clear view of our lower control arm. To service the lower control arm, if you're not replacing the ball joint at the same time, we're just gonna remove this nut, the bolt, and the other nut right here. Okay. So as you can tell, it's starting to put a pressure right up along here. So I'm just gonna leave this as it is for this second and then we're gonna move along to the front bolts right there. Let's remove this 19-millimeter headed bolt.
All right. If your bolt's stuck inside there and you seem like you're struggling a little bit, it's probably just because there's a lot of pressure still. If you wanted to, you can move along to the rearward bolt. Once that's loose, we should be able to move this around and the bolt might come out a little bit easier. The bolt that you can see from the bottom also comes up along the top area right there. We're gonna use a 19-millimeter wrench to hold that nut and then from the bottom we'll remove the bolt. Now that that rearward bolt's loose, this is much looser. So let's get this right out of there. Now that that bolts out of there, I'm gonna take a nice long pry bar. I'm gonna come through the hole in the control arm so I can move this and we'll finish removing this nut. Okay. So let's pry down and separate those two. Now I'm just gonna turn that ball joint so it's out of the way. You wanna be very careful not to damage the boot in any way. At this point, I can bring this control arm up a little bit just like this and it'll apply less pressure to the bolts and we should be able to take it out. Now let's pull the front area out of the subframe and then, of course, pull out the rear area. Let's spray the area with some penetrant just to help it slide out of there. As you can tell, the bushing area is kind of kinked off to the side. That's, of course, gonna jam things up a little bit. So you're gonna need to use a pry bar, do whatever you can. We're gonna pull it straight out towards the front. There it is, friends.
The next thing we need to do is take a look at the mounting areas where the control arm's gonna go. If it looks like it's got a lot of crud or build up, you need to make sure you get it out of there at least as much as possible because we don't want anything restricting the area. Don't forget about the front one. If you have access to any copper Never-Seez, I always like to put a little bit kind of around where the bolt holes are just to help that control arm bushing slide right in. Do it in the back and in the front if you have some. Okay, friends. Now it's gonna be time to install our brand new lower control arm. To start, I'm gonna kind of line it up approximately with where it needs to go. What you're gonna notice is that the bushing itself is gonna be at a little bit of an angle. So you might have a little bit of an issue pushing it in there but what you can do is use a nice rubber mallet, hit along the front here just to kind of drive it in. If it seems as though the bushing is going at too much of an angle, it's gonna get caught, so just go right along the lip with a pry bar and your hammer and just give it a couple of loving bonks until it slides in. So you can see this is going at a severe angle at this point. I definitely don't wanna let that keep going like that, so I'm gonna go ahead and give it a bonk like I said. To continue, what I like to do is just use a nice bungee cord or whatever you might have for a strap and just try to strap it up so there's no way that it can fall down and potentially hurt you while we continue.
Now, the next thing that we need to do is, of course, line up the bushing with the hole at the mounting point. You can go ahead and use a pry bar. And I also like to have a nice screwdriver like this so I can go up through the hole. Use the pry bar, move it around to any direction that it needs to go to be able to line up the hole. To check it, just go ahead and use your screwdriver, come right up through there, and then, of course, you can wiggle it around a little bit to make sure it's perfectly aligned. At this point, let's go ahead and start that bolt in. If your bolts look like this, let's just go ahead and clean them up. Now that we have our bolt threads nice and cleaned up, let's go ahead and start them in here. To start the bolt into the rearward bushing, you're gonna notice that the bushing's more than likely gonna be at an angle. To help you line it up, you can use a shallow socket, put it right on there, and then a nice long extension, and that'll give you leverage to be able to maneuver the bolt as needed. Start our nut on there. If you wanna use a little bit of threadlocker, we'll call it your prerogative. Now, the next thing you're gonna want is a nice pry bar. We're gonna come through the top hole of the control arm just like this and now we'll be able to twist the control arm to be able to get that bushing into where it needs to go. There we are. It's started. So at this point, let's go ahead and drive this in. Let's go ahead and give this a couple of bonks, try to drive it in. Let's line up that hole. Let's try to line up the hole here. Take your bolt. If you wanna use a little bit of thread locker, like I said, your prerogative. Start that in. Now we're gonna line up the lower ball joint with the control arm. Go ahead and press down on that. Shift this so it lines up. And then, of course, start the studs into the holes. Let's snug them up. I always like to start with the bolt first.
All right. Let's go ahead and torque these to 66-foot-pounds. Torqued. The next thing we need to do before we can start snugging up the inward bolts is to put load on the suspension. What I mean by that is you need to jack up right under here. We just kind of wanna make it so that the control arm is sitting as though the vehicle's on the ground. Obviously, if you're working on jack stands or anything like that, you wanna be very careful because you don't wanna shift the vehicle off those jack stands, you wanna make sure you're safe as possible. Now that we have this raised up, let's go ahead and snug these up so we can torque them. Now we're gonna torque both of these bolts to 101-foot-pounds. Let's get this out of here. Let's get our lug nut off of there, get the wheel up on here. We'll bottom out the lug nuts and then we'll torque them to 76-foot-pounds. All right. Let's torque them in a criss-cross manner. Torqued.
Tools used
