Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Highest Quality Materials
Made from highest quality materials that meet or exceed OEM standards
Direct Fit Replacement - Guaranteed to fit and function for your specific application
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the front engine mount. This is a 1998 Toyota Camry. It's basically the same for yje '97-'01 Camry, with the 2.2 liter four cylinder engine, and an automatic transmission. There is a different mount for US and Japan built models, but the procedure is the same.
You'll need a new front mount from 1AAuto.com, 14-17 millimeter sockets with a ratchet and extension, torque wrench, and a jack and jack stands.
This job can be done with the vehicle on the ground. You may not even have to raise and support it, but we've put it on the lift to make it easier to film for you.
Remove the 10 millimeter bolts securing this steel pan to the bottom of the sub-frame. You have bolts hidden here, up under the splash shield in the back. All these along the front, and another one under the splash shield on this side. We'll remove the 10 millimeter bolts with a 10 millimeter socket and ratchet, and an extension if needed. Be sure to secure this pan while you remove the last bolt so it doesn't fall on you.
Remove the 14 millimeter bolt coming from the bottom of the motor mount up through the sub-frame. Use a 14 millimeter socket and ratchet. Use a floor jack under your oil pan to support the weight of the engine while we remove the mount. Remove the bolt on the top of the motor mount with a 17 millimeter socket and ratchet, and a long extension for some access. Remove the remaining two 14 millimeter bolts located on either side of the motor mount. We're going to use a 14 millimeter socket, and I like to use a couple of extensions so I can get enough clearance to swing a ratchet up over the manifold. Jack up on the motor a little. Drop the motor mount down. Remove it from the vehicle.
As you can see, the old mount and the new mount are identical. We have the same three mounting locations at the bottom and a welded nut for the bolt that comes up from the bottom of the sub-frame. They're the same height and shape. You'll notice our new part comes with a stud in it should you decide to use that. Or you can simply spin it out and re-use the top bolt that came off of your old mount.
Install your new motor mount. Line up your rear bolt holes. Start them into the frame. Start the top bolt into the motor mount. Or if you decided to use the stud, you'll thread the nut on at this point. Tighten the remaining two 14 millimeter bolts. Torque the 14 millimeter engine mount to sub-frame bolts to 47 foot-pounds. Torque the bolt from the engine mount to the rubber to 47 foot-pounds. Let the engine off the jack. Reinstall the 14 millimeter bolt on the bottom of the sub-frame up into the engine bracket. Torque the bolt to 47 foot-pounds.
Reinstall the steel pan at the bottom with your 10 millimeter bolts.
Thanks for tuning in. We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
