Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Part Details
TRQ brake kits are designed to restore your brake system to like-new performance. TRQ brake pads are positive molded, thermal scorched, chamfered, and utilize a multi-layer shim for enhanced performance and service life. TRQ rotors have a non-directional finish that reduces the break-in period for new rotors as well as reducing vibrations throughout the rotor’s lifecycle. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Premium Positive Molded Brake Pads Features and Benefits
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Hi. I'm Mike from 1A Auto. We've been selling auto parts for over 30 years.
Use a pry bar, or a large flat-bladed screwdriver to remove the hubcap. Just gonna slide it under the edge. Put that aside. Take a breaker bar and a 21 millimeter socket, and loosen the lug nuts with the car still on the ground.
Raise and support the vehicle. Now you can finish removing the wheel. These lug nuts are pretty loose, so I'm just going to use the socket and take them off. I'm removing the last lug nut. I'm just going to hold onto the wheel so that it doesn't fall off and take it right off.
Start by removing the two caliper pin bolts--one on the bottom and one on the top. Use a 14 millimeter. It actually broke free without having to use the mallet.
If it's tight, you can take a mallet and just tap it to break it free. You can squeeze the caliper a little bit by pulling it out. It should slide right off the pads. Take a bungee cord and just hang it up and out of the way.
So I'm going to use a small pry bar, or you can use a flat-bladed screwdriver. You need to pop them away from the brake rotor and out of the caliper bracket. Remove the caliper bracket bolts. There's two at the back--one on the top and one on the bottom. They're 14 millimeter. They can be in there pretty tight. Use a box wrench and a mallet and break them free.
Going to get the bottom one loose and then work on the top one. See that they've broken free--you can switch to a ratcheting wrench. Got it pretty loose, just got to remove the bottom one with my fingers. Put that aside and reuse it, and get the top one out. Pull the bracket out, and the bolt out.
This car is missing a rubber plug that goes in the rotor here. The rubber plug is so you can access the parking brake mechanism to release it. Somebody just put some duct tape over it. I'm going to peel it off. Inside here is the mechanism. I'm going to try to pull it off first, though, 'cause sometimes it's loose enough, you don't need to release it.
Parking brake's not on--it is spinning free. I can spray some rust penetrant around the hub. A little bit in here. We'll take our dead blow mallet. I'm gonna hit around the edge here to try to break it free.
Sometimes you'll get lucky. These might come off, but they usually get stuck on the parking brake shoes. Need to release the adjustment. It's very hard to see right now, but through this opening, it normally has a rubber plug on it. It had some duct tape on it. We removed it. Take a flat-bladed screwdriver. We're gonna spin it. Trying to grab the little tabs on there and spin it up, it's in a little wheel. Make sure I'm going the right way. You can check and see I went the wrong way. It locked it, so it's going to be actually spun down.
You basically just have to spin that wheel down and keep retracting the parking brake shoes in, so the converter will come free. When you adjust it, you're going through the rotor and into this hole, and then you're pushing down on it. And that spins the parking brake shoes in to release them.
Here's our original pads and rotors from our vehicle, our brand new ones from 1AAuto.com. Same exact style of rotor. Pads are same design--same lug pattern, pusher bolts, holes if you need to, the same access hole for the parking brake, which rides on the inside of the brake rotor hub here. These should fit great and work great for you.
We're going to clean and reuse our brake caliper hardware. It's in the caliper bracket, and I'm going to use the brake parts cleaner. Let's take a wire brush. Use the brake parts cleaner and a rag, and just wipe it down. Typically this hardware is stainless steel, so it can be reused. It doesn't get very rusty. And repeat it for the other side.
Now's is a good time while we have this out, just make sure that your caliper slide pins move freely. These ones move nice and free, and we install that in the car. Install the rotor backwards, take brake parts cleaner, and clean off the oil that comes on these so they don't rust while they're shipped.
Flip it over. Make sure you install it in a way that this hole lines up with one of the openings here so you can adjust the parking brake. Instead of taking the caliper off of our bungee cord, I'm going to take one of the old brake pads, take a ski clamp. And now what I'm going to do is gently compress the caliper, push the piston into the body, and that way when we put our new pads in it'll slide right together. I'm just going to rest the caliper like that.
Take a brake parts cleaner and clean it off. Reinstall our caliper bracket, keep the top one caught first, and it makes it a little bit easier. And I'm going to install the bottom one. It's a little easier, 'cause it just hangs on the top one. Reach in behind here. Put that bracket lined up.
Use the 14 millimeter ratcheting wrench to snug these up. Install our new pads. Just take some brake parts cleaner and make sure they're nice and clean. Brake caliper grease on the ears of them. Inside and outside pads are the same. Let's start with the inside pad. Place it on the bottom clip and push it up into the top clip. It snaps into place. Do the same for the outside one.
We're just following the curve of the pad too, the contoured, so the wider part is gonna match up with the lighter outside part of the rotor--same with the inside part. Just push them down into the clips and squeeze them together. Place the caliper back in place. Reinstall the bolts. Tighten these up. They'll get tight and I will stop.
Torque the caliper bolts to 46 foot-pounds. You need to adjust the drag on the parking brake. You can turn this so you can see the adjuster and then you can put your screwdriver in and just catch the gears in the wheel just right.
So now that's how you'd adjust it so that it's actually really tight. It's holding the brake runner, so now you know where the limit is. You want to back it off a little bit by turning it back down. Eventually if you touch the parking brake pedal it would self adjust out, but this way it just gets it closer right away.
So now I'm going to reach in and turn it down a little bit. So what it's dragging on right now is just the brake pads, but that should spin freely enough. And of course when you hit the parking brake pedal, it should come out and lock the rear wheels.
It's important to note these lug nuts have a taper, taper meets the wheel, matches the inside of the wheel. Don't install them with the flat side like this--that is incorrect. Install them with the taper to the wheel, it helps locate the wheel on the lug nut stud.
I'm just using the socket and ratchet to bring these down snug before I put the car on the ground.
We'll torque the lug nuts to 76 foot-pounds. Going in a cross pattern. We reinstall the hubcap. It'll line up the opening for the valve stem, with the valve stem on the wheel. Just push it in place.
Before we start the car, just going to gently press the brake pedal down, not all the way to the floor, maybe about a quarter of the way, and just pump it, and this will bring the brake caliper piston out to meet the pads, because we can press it, and you'll start to feel it get more solid as it pumps up.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
Tools used
All right, friends, to get started on our front brake job, we need to safely raise and support our vehicle and remove all five of our lug nuts. Remove your wheel. The next thing we need to do is gonna be accessed from the back side of the caliper. We're gonna remove our two caliper slider bolts. Now let's get both of those out of there. Next, we're gonna come into this portion right here and we're just gonna slowly push in our caliper piston. Remove your caliper and put it someplace so it's not putting any pressure on that flex hose. Let's just make sure that that caliper piston is pushed in all the way. And then, of course, we'll just look to make sure we don't see any fluid. This looks good. Set it aside. Attached to the pads, you're gonna see these clips. We need to remove the clips. Remove your brake pad. Set those aside. Now let's remove our caliper bracket bolts. Remove your bracket. Set it aside. Remove your rotor. Now that we have the rotor off there, we need to pay special attention to the wheel bearing. This is gonna be the area that the new rotor is gonna sit on, so it needs to be very smooth. Clean it down. Now we need a nice collection bucket and some parts cleaner. Clean the area. We need to strip down this bracket, and what I mean by that is to take off these tins. Set those aside.
We're gonna grab onto these caliper sliders here, you give them a nice twist and they should wanna come off of the boot. We'll go ahead and pull that out of there and we'll set it on the corresponding side. Do the same to the other one. Now we're just gonna clean down our sliders. We wanna make sure that the one that does have the rubber boot on it, because this one right here does, is gonna end up on the same side that you removed it from. So that's the importance of putting them on their corresponding side. Put this over a nice recycling receptacle and we're gonna put in some parts cleaner. Take a nice bore brush and get right down inside those holes. Let's go ahead and tip this over. As you can see, a lot of gunk came out of there. Give it one last spray and move along. What we need to do next is clean the area where the tins are gonna ride. What I mean by that is take a nice brush, make it as smooth as possible. If you have a lot of large crusties, you might need to use sandpaper or even a chisel of some sort. Now that we have all four corners of this nice and clean, let's move along to just taking a nice clean rag, put it inside of these boots right here, and we're just gonna make sure we get all the gunk out of there. That's gonna be super important. Same thing to the other one.
Okay. Next, it's gonna be time to reinstall our slider pins. When you do that, you wanna make sure you use a good amount of caliper grease. We're gonna go right along that entire slider pin and then, of course, up along this ridge right here. That's gonna be super important to help make sure you keep moisture out of the area. Go ahead and put it in there. We're gonna give it a nice spin as we go. A couple of spins once it's in there. That's gonna make sure everything's settled as it should be, and we'll do the same to the other side. Now let's move along to coating the area that we just finished cleaning down where the tins are gonna ride. Now when you look at these tins, you wanna make it so these areas that are raised and coming out away from the tin are facing away from the area where the rotor would be, which would be in the center right here. Let's go ahead and put this just like this. Squeeze it in so it's locked in, and then we'll continue on by doing the same to all the rest. Before we make our way over to the vehicle with our brand new rotor, it's important to make sure you clean down the braking surface. Don't forget the backside. Let's coat this surface with some copper Never-Seez. Put on your brand new rotor and I always like to put on a lug nut to hold the rotor still. Before we can remount our caliper, it's important to make sure you clean down the threads on your bolts.
Now let's get the caliper bracket on here. We're gonna start in both of our caliper bracket bolts and then we'll snug them up and torque them to manufacturer specifications. Now that they're bottomed out, torque them to 79 foot-pounds. Now it's gonna be time to prep our brake pads. What I mean by that is you have these wear indicators. For the wear indicator on the outside pad, we want that on the bottom side. So we're gonna go ahead and put this just like this. That sets in there, and once the pad gets worn down to this point, it's gonna make an indication of a noise and it's gonna let you know it's worn low. Do the same on the inner pad except on the top. Let's go ahead and put that inner pad in there. Same for the outer. Now let's continue on to adding a little bit of caliper lube around this area here where it contacts the pad, this area, and also along the piston. All the areas that contact against the pad. Now let's move along to putting in these little clips right here. When you put these in, you're gonna have to hold the pads so they can't move and put them just like this so they're gonna be facing towards the inner aspect of the caliper bracket. That's gonna help separate the pads when you release your brake. Okay. Now that we have both of those clips in and they're facing towards the center, let's go ahead and grab our caliper. We're gonna put it over the pads.
At this point, we can release them. Push in on your slider pins so it lets the caliper set in. Start in both of your bolts. We'll snug them up and then we'll torque them to 25 foot-pounds. Let's get our wheel back up on here. Start all of our lug nuts, bottom them out, and then we'll torque them to 76 foot-pounds. Torqued. Go ahead and pump up your brake pedal so it's nice and firm and then check your brake fluid.
Tools used
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
Use a large pry bar for a flat-bladed screwdriver to remove the wheel cover. I'm just going to slide it between the wheel and the plastic. Pop it off. These lug nuts are a 21 millimeter socket. I'm going to use that and a breaker bar to loosen them while the vehicle's on the ground. Then, raise and support the vehicle. We're using a two post lift, but you can use a jack and jack stands. The lug nuts are loose. I'm going to take the socket and finish removing them. I'm just going to hold on to the wheel. I'll take the last lug nut off. It's going to be loose. I don't want to drop it. Drop the lug nut. That's okay. I just don't want the wheel to fall.
Before I remove the caliper, I'm just going to pull on it and try to compress the piston. That way, it will slide right off. Take a 14 millimeter wrench to loosen the caliper slide bolts. There's one on the top, one on the bottom. They're pretty tight. If they don't want to budge, you can take a mallet to break them free. Same thing on the bottom one. I've got a bungee cord handy, so when I remove these caliper slide bolts, I could hang the caliper from the strut. Let's loop it around. The caliper should slide right off. See, one of our hardware pieces of hardware is actually broken on here. It should go right in there. The pads will slide right out like this.
Two 17 millimeter bolts that are holding the caliper on. There's one on the top and one on the bottom. To break them free, you can use the box wrench and the mallet. We've got these loose. I'm just going to remove them by hand.
The rotor is very loose. We don't want it to accidentally fall. I'm just going to take one of the lug nuts. Just put it on there so it doesn't fall on my feet. Remove the caliper bracket. So we're pretty lucky. This brake rotor's really loose. I'm going to take the lug nut off that I was using to hold it on, just slide it right off the studs and the hub. If it was rusted on, you could thread a couple of small bolts into here and evenly turn them down or push against the hub and push the rotor off.
These are old pads and rotors for our vehicle. I've got brand new ones from 1AAuto.com. So the pad design is very similar. The rotor design is the same. Five lug holes, two pusher holes. It's a ventilated rotor. This will fit great and help the car stop.
Before you put the rotor back on the hub, make sure it's nice and clean, not too rusty. This one's in good shape. If yours is really rusty around the hub here, take a wire brush and knock some of the rust down, clean it off. We're going to take our new rotor, and we'll install it backwards first. Take our brake parts cleaner, and we're going to clean off the oil that they ship with so they don't rust. Grab it, flip it over, install it the correct way. I'm just going to throw a lug not on here so it's not moving all around on me. Take a brake parts cleaner. Clean the surface. I'm just going to wipe down any excess.
You need to compress the cylinder back into the brake caliper. I'm taking the old brake pad, and I've got a C-clamp, and gently compress it. This way, our new pads that are thicker will fit. We need to clean our hardware so we can reuse it. We'll take some brake parts cleaner and just spray it in there. Get a wire brush. Just repeat for the other side. We're going to reinstall our bracket. Get those started by hand. The top one's usually easier to get done first, and you can move this one in and out to line it up. I'm just going to snug them down. Take some brake parts cleaner to just make sure the pad surface is nice and clean before you install them, and put just a tiny amount of brake caliper grease on the ears of the pad. Don't need to go crazy with this stuff.
The inside and outside pads are identical, so I'm going to start with the inside one. Pop it into the bottom, push it in. Repeat for the other pad. Clean it off. Put a little bit of grease on the ears. Replace the spring hardware, put it in place. It's going to balance the caliper. Swing it down. Get the back part caught first. Push that over. Caliper slide bolts and reinstall those. Get a 14 millimeter ratcheting wrench. Tighten them up, and torque the two caliper bracket mounting bolts to 79 foot-pounds. Don't forget to remove the bungee cord you were using. Make sure the brake rotor is clean. Sometimes, you get dirty fingerprints on it. I'm just going to double check that these are tight.
I'm going to reinstall our wheel. It's important to note these lug nuts have a taper. The taper meets the wheel, matches the inside of the wheel. Don't install them with the flat side like this. That is incorrect. Install them with the taper to the wheel. It helps locate the wheel on the lug nut stud. I'm just using the socket and ratchet to bring these down snug before I put the car on the ground, and torque the lug nuts to 76 foot pounds. I'm going in a cross pattern. We'll reinstall the hubcap. I'm going to line up the opening with the valve stem, with the valve stem on the wheel. Just push it in place.
Before we start the car, I'm just going to gently press the brake pedal down. Not all the way to the floor. You need about a quarter of the way, and just pump it. And this will bring the brake caliper piston out to meet the pads, because we compressed it. And you'll start to feel it get more solid as it pumps out.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
