Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Part Details
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Formaldehyde and Toluene, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the driver's side wiper arm on this 2002 GMC Sierra 2500 HD. It's the same process on the passenger's side, and it's the same process on pretty much any 2000 to 2002 GMC and Chevy truck. The only tools you'll need include a small flat blade screwdriver, 13mm socket and ratchet, and some penetrating oil.
Use a small flat blade screwdriver and pry off the cap and that exposes a 13mm nut. You want to disconnect the washer hose and remove that 13mm bolt. Next, what you want to do is push the windshield wiper down just to try to loosen it up a little bit, and then spray some penetrating oil onto the bolt there. That'll help to get this off. After it sits for a little while, then you want to push on it some more and that should actually just pop the arm right off.
Now, to remove the wiper blade, push that switch and just pull the wiper right off. You can see here the old wiper arm and the new wiper arm from 1A Auto. It's an exact replacement.
Just put the wiper blade onto the new wiper arm. You just want to push the wiper arm back into place, and then you want to replace that nut and tighten it. Then you're going to put the cap back on and reconnect your washer hose.
Now, you want to test your windshield wipers. Make sure the washer hose is connected correctly and that they're lined up properly. If they're not, you're going to want to remove that nut and realign the wiper arm, and then you should be all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Okay, friends, to start this job, obviously, the hood needs to be up. The next thing we would want to do is just kind of take a nice look at this and kind of gauge approximately how high the wiper blade is going to sit on the windshield. The next thing we want to do is just follow the arm down to this point right here. There's a little cover. Go ahead and take that off of there. Underneath that, you're going to see a 13-millimeter nut. More than likely it's going to be rusted like this one, so go ahead and hit it with some penetrant. Now that we've let that sit for a little while, let's go ahead and remove that nut. All right. Let's grab onto this and just see if we can wiggle it around. What we need to do is get the arm to break free from this stud. You might notice it doesn't want to. Okay. So, it's pretty obvious in this case that this is not coming off. I don't need to go any further. I don't want to break anything underneath it. The next thing I would recommend is a tool that looks a little like this, and this is going to help get that off of there.
I'm gonna take the two ears, slide it around the bottom side of the arm here, and then I'll go ahead and drive that driver down and it should separate the two pieces. There we are. Get the tool off of there. Now, we can lift this right up and off. So, obviously, our hose is still attached to this right here. This is a nice 90-degree bend, and our new part comes with a new one. If yours isn't broken or leaking or damaged in any way, I would probably just leave this in where it is and remove the hose directly from it. The reason for that is because if I go to remove this and it breaks something down inside there, it's going to lead to a further issue and I'll have to remove this whole cowl. A simple way to get this off would be using something like a razor blade and you can just go ahead and cut that hose, grab onto it, and remove it. The next thing I would want to do is get the blade right off of here. If you were to lift up like this, you can see there's a little tab, squeeze that tab, and then we can separate the two. Inspect your blade, make sure it's in good condition. If it needs to be replaced, well, now's the time to do it.
Now, we have our new arm and our wiper blade. Let's go ahead and put the hook in. See if I can get it through there, lock it in, give it a nice push. Make sure that the wiper blade is completely secured. Let's put this right up and in here. We've got our hose. It needs to come up and over and then we'll put this on, and then, of course, the hose will make its way down and over there. Let's get this lined up to approximately where it was. That looks decent. Now, I'm just going to press this down so that it's sitting over the stud there. Take our nut, start it on there. Go ahead and snug it up. Okay. Not pretty much bottomed out, teeny bit more, give it a nice wiggle, make sure that it's completely secured. All right. So, let's go ahead and twist that back in the direction it needs to go. Now, if you're not replacing this piece right here, you should be able to just kind of grab onto it. And if you're strong enough, you should be able to pull it off. If for some reason you couldn't pull it off, you can go ahead and trim off the very end of it. And as long as you have enough slack so that you can get right onto this right there, my finger out of the way, comes around, push it right up on there. You want to make sure you have slack coming right around this, okay? It's going to come out right up and around the top, and it just kind of hangs out there. You want to make sure that it's not so short that when the wiper arm comes up or goes down, it puts a tug on this hose. Do not forget about our little cover here. Go ahead and slide it on over that. Now it's going to be time for a test. Awesome.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace a wiper arm on this 2002 Chevy Suburban. We show you on the driver's side, but the passenger's side is a similar procedure. It's the same part and similar process on these Suburbans from 2000 to 2002. The items you'll need for this is a new wiper arm from 1AAuto.com, flat blade screwdriver, and a 13mm socket and ratchet.
Start off by pulling out your washer hose and then remove this cap. It's easiest if you use a flat blade screwdriver and just pry it off. Then you want to remove that 13mm nut. We'll fast-forward as Don does this. Now, pump the wiper arm in and out a couple times to just loosen it up, tilt it up, and pull it off the stud. Now push the tab on your wiper blade and slide it off that hook.
Up front is your old wiper arm; behind it is the new one from 1A Auto. You can see they're identical, and they're going to fit exactly the same. Take your wiper blade and slide it onto your new wiper arm. Then line up your wiper arm, push it onto the stud, make sure it's where you want it, and then replace that nut and tighten it up. Now replace the cap, then push your washer hose back into place. You're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
