Replaces
Frequently bought together
Item Condition:
New
Attention California Customers:
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we'll be showing you how to replace the driver's master window switch on this '05 Camry. You'll need a Phillips screwdriver and a flat blade screwdriver.
Use your screwdriver. We're just going to put it down in there and pry. It may take a couple tries. Pry that little rubber pad out of there and then there's just a Phillips screw right under there. Remove the Phillips screw. This whole panel lifts right up, back, and out. Underneath, you can disconnect your mirror. There's a little tab right there. Then to disconnect this, there's a tab here, which you pull back on and then disconnect it.
Now, my switch works fine, so I'm just going to show you this, but to change your power window switch, there's three Phillips screws. The switch comes up and off. You'll see this is all one piece. You'll see.
Reinstallation: just reverse the procedure. Plug in your gear harness. There's a little collar that slides. You would pull that way back, then put your connector in, slide it down, and lock it on. It just slides forward and down and in. Put your screw back on.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the front power window switch on this 2008 Toyota Sienna. It's pretty much the same as a 2004 to 2010 Sienna. The only tool you'll need is a Phillips screwdriver.
To remove your window switch, pull up here, and there's a screw right here to remove. Once you have that screw removed, work your fingers underneath and pull up firmly on there. Pull this up, slide it back, and this all comes out. Your harness connects right here. There's a tab right here. Pushing on the tab, just pull back on the plastic. You don't want to pull on the wires. Pull back on the plastic. See how the plastic comes out and it disconnects. Pull that plastic back to make sure it actually will reset.
Now, pretty easily, three Phillips screws hold your switch in. Make sure you set this aside, the little tab, and then you've got two screws. Then your switch comes out.
The new switch from 1A Auto looks the same as the old switch and mounts the same as the old switch, but it'll work better than the old switch. A lot of times what happens, is you accidentally leave your window open, or maybe you spill some coffee, and it shorts out these switches. I'm going to put the 2 back screws in first. Just put them in a couple of threads down there. Remember this tab. Pull up the switch a little bit. Slip the tab under there. Hold the switch down. Put my third screw in. Get that in and get it nice and tight. Then I'll tighten up my other two. As I said before, make sure that's reset and pulled back. To put it in, just put a little pressure on the wires. Then put that plastic in, slide it right in and inspect it. Get the wire down in. Push that tab in, back down in. Make sure that clip's lined up, and down on. Open the arm rest. Put your screw in, and you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
