Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Item Condition:
New
Attention California Customers:
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we are going to show you how to replace the main power window switch. This is a 1998 Toyota Camry and the items that you are going to need is a new side window switch from 1AAuto.com, a flat-blade screwdriver, and a Phillips screwdriver.
The steps to remove the master window switch and the passenger window switch are very similar. They are nearly the same, but the switch itself will look just a little bit different. Using a flat blade screwdriver, pry up on the back to release it from the door panel. Lift up.
Pull to the back to release this hook from underneath the panel. Press down on the tab to release the connector. This one is a little stuck. Use a small screwdriver to help release it. Remove the three Phillips-head screws with a number two Phillips screwdriver. Remove the switch from the panel.
Here we have our old master window switch from our vehicle and our new part from 1AAuto.com. As you can see, the switches are the same size and shape. The graphics are a little bit different, but it's still going to work just the same. We had the two position automatic down feature on the driver's window switch. All the other switches work nice and smooth. These are all full of dirt and grime from being in the vehicle for almost 200,000 miles now. Some nice, smooth switches here. We're going to have good contact.
Make sure your windows go up and down every time you want them to. Also, the door lock feature is being located here, and the safety to disable the passenger and rear windows. We have the same connector on the bottom. We have the same two pins at the bottom, one pin at the top. You can see it fits into our trim nicely. It'll go right in, direct fit just like our original equipment.
If your window switch is broken, sticky, or not doing everything it should, this new part from 1AAuto is going to fix you up right. We have our new switch from 1AAuto.
We'll reinstall the trim for our vehicle with the three Phillips head screws. There is no need to put these in real tight. Just get them in there snug. You don't want to break the plastic.
Reinstall the connector into your switch. Slide the front hook under the door panel, and snap the rear into place. Check for proper operation of your switch.
Our door won't stay locked because the driver's door is open and the key is in the vehicle. Lock and unlock work fine. The window goes up. Now, sometimes you have to program the automatic down feature when you get to the bottom. Push the switch all the way in and count 10 seconds. Roll the window all the way up and then try the auto down feature.
Thanks for tuning in. We hope this video helped you out. Next time you need parts for your car, please visit 1AAuto.com. Also check out our other helpful how-to and diagnosis videos.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
In this video, I'm going to show you how to replace the driver's master window switch on this '98 Corolla, the same as any '98 to '02. The indication that your window switch isn't working is when you press it none of the windows make any noise. These can get shorted out by water if you leave your window open. The only tools you'll need are a small flat blade screwdriver and a Phillips screwdriver.
Pry this front corner here up, pull your plate forward and up and out. Now, there's a little button right under here. Press that button. Now the switch is held on to the panel with three Phillips screws. The switch comes off the panel. A brand new switch from 1A Auto is the exact same, just a little cleaner and it will work better. We'll fast forward. Notice I start all three screws first, then kind of do a preliminary tighten with the screwdriver and then tighten them down firm, but don't over-tighten them. With the new switch in, put the back down in first, slide it back, and press it into place.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
