Chevrolet GMC Cadillac Front 11 Piece Steering & Suspension Kit TRQ PSA58716

You wanna keep in mind when you're doing this job, after you're done, you're gonna wanna go to a local garage and have the vehicle aligned so you don't have premature tire wear.

Take this center cap off. We'll just use a straight blade screwdriver. Just get behind here, slide it off. Get the lug nuts off. Use a 22-millimeter socket. Now take the wheel off.

Loosen up this jam nut. I'm gonna use a 7/8 wrench. And just take some rust penetrant, this thing's a little bit rusty. So let that soak a little bit. Now take a 18-millimeter socket. Take this nut off. And take a hammer and just hit the bottom of the tie rod to release it from the knuckle. Just like that. Now I'm gonna take off the tie rod. Just count how many turns you have. So 1, 2, 3, 4, 5, 7, 21, 22. And write that number down. And take the outer tie rod, one, two. And then count the turns that you counted before, 3, 21, 22. Take the jam nut off. I mean, the castle nut off. And slide it in the knuckle. Slide the stud part into the knuckle. Put the nut on. Just gonna use a pry bar. Pry down on the outer tie rod end to prevent the stud from spinning. And just snug this up a little bit. It's the 18-millimeter socket. And torque this to 37-foot-pounds. And if the hole doesn't line up for the cotter pin, just tighten the castle nut until it lines up. Little more. Should be good. Put the cotter pin through. And take my cutters and just bend this over. And just trim the excess. Tighten up this jam nut. I'm gonna use a 13/16 wrench. And if you have the ability to torque it, torque it to 36-foot-pounds.

Put the wheel on. And the lug nuts. And now I'm gonna torque these lug nuts in a star pattern or cross pattern to 140-foot-pounds to tighten the wheel down evenly. And just go around again. Double-check. And put the center cap on.

You want to keep in mind when you're doing this job after you're done, you're going to want to go to a local garage and have the vehicle aligned so you don't have premature tire wear. Take the center cap off. I'll just use a straight blade screwdriver, just get behind here, slide it off. Take the lug nuts off. Use a 22-millimeter socket. Gonna take the wheel off. [inaudible 00:00:34] off this jam nut. I'm going to use a 7/8 wrench. And just take some rust penetrant, this thing is a little bit rusty so let that soak a little bit. Gonna take a 18-millimeter socket, take this nut off. And take a hammer and just hit the bottom of the tie rod to release it from the knuckle. Just like that.

Now when I take off the tie rod, just count how many turns you have. So 1, 2, 3, 4, 5, 7...21, 22 and write that number down. Now I'm going to take a large adjustable wrench and loosen up the inner tie rod end. And loosen this up and just slide it off. Take a little thread locker, put it on the threads before you put the new one on and line it up. And then use my adjustable wrench to tighten this up. If you have the ability to use a torque wrench and torque this, you want to torque this to 74 foot-pounds. And take the outer tie rod, one, two, and then count the turns that you counted before. Three...21, 22. Take the jam nut not off...I mean the castle nut off and slide it in the knuckle. Slide the stud part into the knuckle. Put the nut on. Just gonna use a pry bar, pry down on the outer tie rod in to prevent the stud from spinning, and just snug this up a little bit. Use the 18-millimeter socket. And torque this to 37 foot-pounds. And if the hole doesn't line up for the cotter pin, just tighten the castle nut until it lines up. Little more. Should be good. Put the cotter pin through. And take my cutters and just bend this over then just trim the excess.

Tighten up this jam nut. I'm going to use a 13/16 wrench, and if you have the ability to torque it, torque it to 36 foot-pounds. There's a grease fitting right here. Just take a grease gun and give it a couple pumps. And I really give it a couple of pumps until I see the boot move a little bit. And that's good. Put the wheel back on. And the lug nuts. And now I'm gonna torque these lug nuts in a star pattern or cross pattern to 140 foot-pounds to tighten the wheel down evenly. And just go around again, double-check. And put the center cap on.

All right. So one of the first things you need to do is safely raise and support the vehicle. Once you've done that, you're gonna remove all six of your lug nuts. Remove your wheel. Now what we're gonna do is we're gonna get the ABS wire out of the way. The last thing we wanna do when we're doing any of the work on this upper control arm is to put a tug or damage this in any way. If you were to follow it up, you'll be able to see right where the connector is. I'm gonna remove that connector from the frame using my forky tool. Pull it down to where you can see it. Grab this tab. Lift it. Pull it off. These right here, you can remove. Just use a small pocket screwdriver or whatever you might have. Get right in between this area right there. We'll do the same down the line. Let's work on getting this brake hose off of the control arm now. We're gonna remove this 10-millimeter headed bolt. That's very common for them to break. Kinda wiggle it around. Get it off of there. The next thing we need to do is come right down here. We need to remove this upper ball joint nut. Once we remove that, we're gonna break the knuckle free from the upper ball joint control arm. There we go. Get that off of there. Put that nut on there. Just a couple threads and I'll show you why in a second.

The next thing we're gonna do is use our pickle fork and our hammer, then we're going to come right in between this joint and separate the two. When it separates, the knuckle is gonna wanna drop and move away. If it dropped and moved away, there's a possibility that it could put a tug on your axle or even maybe something such as your brake hose. We don't want that to happen. That's what this nuts for. It's a safety nut. Leave that there for now. So now I'm just gonna use a bungee cord or pretty much anything that you might have that can prevent this from falling down because we need to get that nut off there but we still wanna make sure we have control of this. There we are. Carefully set that aside. Let's spray this down with some penetrant. Take a peek right under here and make sure that you don't have a snap ring. A lot of vehicles won't, yours may. Now it's gonna be time to get our ball joint press set up on here. You're gonna need a cup that fits directly over the top of that ball joint up all along that control arm. You're gonna need a piece like this that has a spot in the center that the driver's gonna sit right into. Now we'll just go ahead and put this right over that ball joint stud and then we'll snug this up.

Now we're just gonna go ahead and tighten this up. And we're trying to press the ball joint up and through the control arm. You can't really see much of what's going on but what should be happening is the ball joint's gonna be coming up and separating. So it looks like that's working pretty well. I can see it starting to separate right there. So what I'm gonna do next is I'll loosen this back up and now I'm gonna try using something else as a spacer to continue driving this up. Get that boot off there. And there it is friends. Just a quick overview of the new ball joint before we go ahead and install it. If you were to look at it, it pretty much looks the same all the way around unless of course you took the boot off and then you took a peek underneath. If you look, you're gonna see there's a flat edge there and a flat edge here. You need the pivot point, which would be the opened areas of this ball joint, to be facing in and out of the vehicle or to the left and the right, not front to back. You don't want this to pivot front to back. That's not the way it needs to go. It would need to go this way so I can pivot in and out or left and right on the vehicle. All right. So we've got our ball joint here. You can see it comes with a little hole on the top. We're just gonna line that up facing straight out towards us. That looks pretty great.

Now I'm gonna take my ball joint press kit and I'm gonna use the piece that looks like this. That's gonna sit right over the top and that's where the driver is gonna go down against. You need to have something covering this ball joint. You cannot press directly against it. I'm gonna use a cup that has a hole in it on the bottom for the lower part. Come right in just like this. And having the hole in the bottom is gonna make it so that the stud will be able to come through as the ball joint presses in. Start that right on there. Now I'm gonna snug this up. All right. Let's go ahead and bottom this out. We're gonna bring the ball joint right down to the control arm. As we do this, you wanna make sure the ball joint's going as straight down as possible. If it seems as though it's going off-kilter in any direction, you need to stop, try to fix the ball joint, straighten it out. Now I'm just gonna take a look. I can see the ball joint is hitting directly against the control arm. I'm gonna double check to make sure it's all the way around. That looks perfect. While we still have the press on here and it's giving it a lot of force, I'm just gonna bonk on this control arm a couple times just to cause a little bit of vibration and maybe set this in if it's just got a little bit more to go. That's great. Let's get this out of here.

It's super important to make sure that you put your snap ring on here. The snap ring is gonna keep this ball joint from eventually or potentially working its way out of the control arm. Grab some pliers that look like this. They're gonna have two little pitons on them and they're gonna fit right inside the holes on the snap ring. Once you spread them, you'll notice that it opens up. We're gonna come right over the ball joint and we're gonna put it up into that lip that's up near the control arm. We've got that over there. Double check to make sure it's seated all the way around. It needs to be in there completely. That looks perfect. Let's grab the boot. So let's turn over our boot and take a little look right here. You're gonna see where the stud comes through. It has a little area that looks different than the rest. That area needs to be facing in-board or towards the inside of the vehicle. So we'll put that facing just like that and it's facing towards the frame. Now we can take some pliers or whatever you might have and we need to get the boot so it's sitting up on top of the ball joint. Double check the boot. Make sure it's sitting perfectly all the way around. As long as it is, now we're gonna grab the knuckle. Bring it up. We're gonna put the stud through. We're gonna need a little bit of leverage though.

I'm gonna use a nice long pry bar. Come across the top of the control arm here/ball joint and under the frame. I'll pull it down and then I'll start in the nut. Give this a little turn. Bring it up. Okay. Let's get our pry bar. Bring that ball joint down and into the knuckle. There we are. Let's start the nut on. Just go ahead and get this thing so it's snugged up. Okay. The torque for this nut is 37 foot-pounds. Will you be able to get a socket and a torque wrench in between here? Probably not. 37 foot-pounds isn't really very much but it is definitely tight. So bottom it out, give it a little bit more, and then we're gonna definitely make sure that the cotter pin hole is gonna line up between the nut and the stud. Okay. So now I'm just gonna take a peek and I can see where the slot and the nut is, and I can see where the hole and the stud is. You wanna line those up. Put the cotter pin through just like that. Now we'll just peen this down and then curl it over. This is gonna make sure that there's no way that that nut can loosen up on its own. At this point, we don't need this on there anymore. Let's get that ABS wire back connected. Give it a nice tug. Make sure it's completely connected and now make sure it's secured to the frame. The next thing you would wanna do is make sure you secure your brake hose.

Go ahead and put that bolt back in, assuming yours didn't break. If it did, you need to make sure you secure it with something such as maybe a tie of some sort, or even drill out the hole and re-tap it if you needed to. Now before we go ahead and put the wheel back up on there, just double-check everything. Make sure that your ABS wire is connected. Make sure your ball joint's sitting flush. The boot's on the way that it needs to be and you definitely have a locking cotter pin holding that nut on the stud. Now let's go ahead and torque our lug nuts to 140 foot-pounds. Center cap, go ahead and pop it on there. Now that you've finished your service, go ahead and take it for a road test and make sure you get it down to a local reputable alignment shop.

Now one of the first things you're gonna wanna do before you start any job is to make sure you're safe as possible. You wanna have safety glasses and hand protection at all times. The next thing you're gonna wanna do is safely raise and support your vehicle so that your wheels are off the ground. Next, if there's a center cap, remove the plastic center cap and that will expose your lug nuts. Remove all 6 using a 22-millimeter socket. Remove your wheel. Now that we have a nice clear view of our tire rods, I'm gonna spray down this area right here. This is the adjustment area. Use a little bit of penetrant. That's gonna help you along. Using some nice long pliers, I'm gonna grab right onto this and I'm gonna turn it clockwise. That'll break free this jam nut. Okay, that broke free. Let's remove the nut that holds the outer tie rod end to the knuckle.

Now we're gonna hit right here on the knuckle to break our outer tie rod end free from the knuckle. Turn your outer tie rod end counterclockwise and count the amount of times it turns around as you remove it. One, two, three and so on. Okay. Write down that corresponding number so you can remember. We have our outer tie rod end. Let's go ahead and put that on. And we're gonna count it in the same amount of threads that we counted the original one off. That was one, two, three and so on. Okay. Just bring this so it's close. Get that nut off of there. I'm gonna put this on there. Let's bottom that out. Now we're gonna torque this nut to 48 foot-pounds. All right. So now that we have that torqued, we need to pay special attention to where the slot on the castle nut lines up with the hole in the stud. If it doesn't line up, you need to continue tightening until it does. Okay, so that looks pretty good. Let's try it.

That slides right through. Spin it over. The cotter pin's gonna ensure that there's no way that this nut can come loose. Now it's gonna be time to tighten up your jam nut. To tighten this we're gonna turn it counter clockwise. When you torque it, you would wanna torque it to 37 foot-pounds if you have the ability. Let's see here. Okay. Just make sure that it's nice and snug. By the time you're finished, make sure your outer tie rod end is nice and parallel to the ground or at least as parallel as it can be. Now let's get the wheel back up on here. Okay. Now with the wheel barely on the ground so it can't spin, we're gonna torque the lug nuts to 140 foot-pounds. Torqued. If you have a center cover, put it on there now. Now that you've finished your service, go ahead and take it for a road test and make sure you get it down to a local reputable alignment shop.

All right, friends. So, one of the first things we need to do is safely raise and support the vehicle. Once you've done that, you wanna come right upfront to this skid plate right here. Go ahead and remove all 15-millimeter bolts that hold it in. Now, that that's out of the way, let's come right over here to where the idler arm comes down through this arm right here, remove the 21-millimeter nut.

Now, the next thing we would need to do to get this arm out of here, is of course try to drop this sway bar out of the way. If your bolts look like ours do, and you think that they're gonna be an issue, I would just skip right past that and we'll come right up here and we'll remove the whole idler unit right here. To get this out of here, we're gonna use a 21-millimeter right there, and then we'll use a 21-millimeter wrench on the nut side.

Let's put a nice piece of wood in between the frame and this bar right here, just to make it so this bar can't go up too far while we hammer on this right there. Now that that's out of there, we can grab right onto this and we'll get it out of the vehicle. Now, when you're replacing your idler arm bracket assembly here, you're gonna have to remove it from the idler arm. To do that, you'd remove this nut right there, and then you'd do something as simple as a pickle fork coming in between here, or you could even use a puller to separate the two. Odds are, if your idler arm bracket assembly is no good, more than likely at the joint at the idler arm itself is no good as well. In which case I would just replace the both as a pair, that's much easier that way as you can tell. But for the purpose of this video, I'll still show you how to get them apart.

Now to remove this, I like to have it nice and level on the ground and I'll put my foot on it. I'm gonna have it so it's facing down towards the left, so when I remove this and it tries to spin, you can't go anywhere. I'm just gonna use this pickle fork right here, put it right in between the joint, and then give it a couple of loving bonks with my hammer. As you can tell, the two separated at this point, this joint is no good, but that's okay, we're replacing this anyway.

The next thing I like to do is put the unit right inside of a vise if you have access to one. You wanna grab onto this boot, take a look underneath there, make sure there's plenty of grease, go ahead and push it down, that feels great. Now we're gonna take that idler arm, set it right down on there. Take our brand new nut. You always wanna use a brand new nut, okay. So, now if I use my 24-millimeter wrench and I try to tighten this, what you're probably gonna notice is the stud on the inside is gonna start spinning once it gets to a certain point. Okay, so as you can see, it's spinning the stud. Is the nut all the way down? No it's not. So, now we're gonna use a hex bit and you wanna use an 8-millimeter. Come right inside there, that's gonna hold it and now we'll continue tightening this. Make sure it's nice and tight. That feels great.

It may be time to get our unit back up inside the vehicle here, spring it right up and in. Behind those lines, hopefully. Get that in the center link. Let's get this into its bracket. Okay, that looks decent, let's grab our two bolts. Make sure that they have washers, there right through. The other one, here we are. Let's grab the washers and the nuts for the other side. Now let's snug these up. Now let's go ahead and torque these down to 73 foot-pounds

Torqued. Let's get this nut on there. Snug it up, torque this to 46 foot-pounds. Torqued and use our locking cotter pin, slide it right on through there. And then make sure you pin it over, so there's no way this nut can come loose. Get this out of here. Awesome. Let's get this shield back up on here on, I'm gonna line up those holes. Start in all the bolts, before I tighten any of them down. Perfect. The next thing that I would wanna do, is make sure that I get it down to a reputable alignment shop.

Now one of the first things you're going to want to do before you start any job is to make sure you're safe as possible. You want to have safety glasses and hand protection at all times. The next thing you're going to want to do is safely raise and support your vehicle so that your wheel is off the ground. Next, if there's a center cap, remove the plastic center cap and that'll expose your lug nuts. Remove all six using a 22-millimeter socket. Remove your wheel.

Now that we have a nice clear view of our tie rods, I'm going to spray down this area right here. This is the adjustment area. Use a little bit of penetrant. That's going to help you along. Using some nice long pliers, I'm going to grab right onto this and I'm going to turn it clockwise. That'll break free this jam nut. Okay, that broke free. Let's remove the nut that holds that outer tie rod end to the knuckle. Now we're going to hit right here on the knuckle to break our outer tie rod end free from the knuckle.

Turn your outer tie rod end counter-clockwise and count the amount of times it turns around as you remove it. One, two, three, and so on. Okay. Write down that corresponding number so you can remember. Now it's going to be time to get the inner tie rod end off of here. Here's the new inner tie rod end. And if you were to look right along this edge right here, that's the area we're going to need to grab onto, and then turn this counter-clockwise to break it free and eventually remove it. So we'll come right under here with our nice long pliers and get it off of there. There we go.

There it is friends. Now it's going to be time to install our new inner tie rod end. You might notice that there's no grease fitting to be able to grease this. Really there is. The grease is going to come right through that hole right there and that'll happen through here, starting at this point right here at this fitting. Put grease here, it comes right through and then of course it fills up the boot on the inner tie rod end. All right. I put some thread locker on here. I'm just going to go ahead and start this thing by hand. Now that we have that, as far as we can get it by hand, let's go ahead and snug it up with our pliers. Bottomed out. Just give it a teeny bit more. Awesome. Let's remove that jam nut. Let's put a little bit of copper never seize on the inner tie rod end threads, and then we'll just work that jam nut up the inner tie rod end quite a bit here. Now that we have the threaded area coded, we have our outer tie rod end, let's go ahead and put that on. And we're going to count it in the same amount of threads that we counted the original one off. That was one, two, three, and so on.

Okay? Just bring this so it's close. Put that node off of there. Put this on there. Let's bottom that out. Now we're going to torque this nut to 48 foot-pounds. All right. So now that we have that torqued, we need to pay special attention to where the slot on the castle nut lines up with the hole in the stud. If it doesn't line up, you need to continue tightening until it does. Okay. So that looks pretty good. Let's try it. That slides right through, just pin it over. The cotter pin is going to ensure that there's no way that this nut can come loose. Now it's going to be time to tighten up your jam nut. To tighten this, we're going to turn it counter-clockwise. When you torque it, you would want to torque it to 37 foot-pounds if you have the ability.

Okay. Just make sure that it's nice and snug. By the time you're finished, make sure your outer tie rod end is nice and parallel to the ground or at least as parallel as it can be. Now it's going to be time to get the grease fitting out of here. Use your 8-millimeter. There it is. Let's clean off around the area. Grab your new grease fitting. We'll start it right in there by hand, and then we'll snug it up, nice and tight. Let's give it a little grease

Now let's get the wheel back up on here. Okay. Now with the wheel barely on the ground so it can't spin, we're going to torque the lug nuts to 140 foot-pounds. Torqued. If you have a center cover, put it on there now. Now that you've finished your service, go ahead and take it for a road test and make sure you get it down to a local reputable alignment shop.

You wanna keep in mind when you're doing this job, after you're done, you're gonna wanna go to a local garage and have the vehicle aligned so you don't have premature tire wear.

Just take this cover off. Use a 15-millimeter socket. There's two bolts on the bottom, two on top, sometimes there'll be a third. Slide it off. Take this cotter pin out. Just use some side cutters. And pull that out. Just gonna use a little rust penetrant, it's a little rusty. Take a 21-millimeter socket, take this nut off. Now I wanna separate the idler arm from the steering bar. I'm just gonna use a front-end [SP] tool. There's many different tools you could use to get this off. Just tighten this up. Put the nut on just so my tool doesn't slip off the stud. Just gonna use it as a guide. Another way you could try do this is use the pickle fork. There we go. Slide that out.

Gonna take these two bolts out. I'm gonna use a wrench, a 21-millimeter wrench backside to hold the nut. Use a 21-millimeter socket on the bolt. Take both of those out. Pull the bolts out. Just grab the whole idler arm assembly and just slide it out.

If you're gonna replace just the arm or just the assembly, you're gonna have to separate it. So use a 24-millimeter socket. It helps to put it in a vise. And then you can use a puller and separate these two. Just like that. And take the arm, put the new nut on. Just snug that up tight.

All right, just line this up. Gonna have to tap this in place. It's good.

Before you put the bolts through up top, just make sure it's going through this bar right here. We'll put the bolts in. Take the two nuts, get them on the backside. Now snug these up. Torque these bolts to 74-foot-pounds. And take the castle nut, install that there. Tighten it up. Then torque this to 46-foot-pounds. If the hole didn't line up you can just tighten it up a little bit more so you can put the cotter pin in. Slide the cotter pin in. And just bend one of the tabs over. And trim the excess. Take the shield, install it. Put the bolts back in. And tighten these up.

Before you start, you wanna be aware that after you're done this job, you're gonna wanna go to an alignment specialist so that you can have the vehicle aligned so you don't wear out the tires prematurely.

I'm gonna remove the wheel. Use a 22-millimeter socket, take the lug nuts off. And take the wheel off.

I'm gonna loosen up the jam nut. You can use a 22-millimeter wrench or a 7/8 wrench. Just get that loose. That's good. I'm just gonna spray a little rust penetrant on here. Gonna use an 18-millimeter socket, take this nut off. And if the nut doesn't come off and the stud starts spinning, you can use an 8-millimeter socket to hold that stud from spinning and then just use the wrench to take the nut off. Now you can take a hammer and just give a tap on the bottom of the tir rod or take a pickle fork and separate it this way. Just if you use a pickle fork, it's probably gonna rip the boot right here. So I'm just gonna give it a hit right here. There we go. And now we're gonna take the outer tie rod off. As we unscrew this, just count the threads. So 1, 2, 3, 4, 23, 24. So write that number down and when you go to put it back together, you're gonna count them to put the other one in the same position that that one was in.

And take the new tie rod end. Get this started. Make sure you count. One, 2, 3, 4, 5, 22, 23, 24. And line this up in the knuckle. Take the castle nut. Get that started. Now what you can do is to prevent the stud from spinning, you can take a prybar. Just pry in between the knuckle and pry down on the tie rod. Use an 18-millimeter socket and tighten this up. And tighten this to 37 foot-pounds. And then just check to see where the stud...where the hole is for the castle nut and if you need to, you can snug it up a little bit more to get it to line up. And that hole lines up. Now take the cotter pin, slide it through. Should slide through this way. And take some side cutters and just bend it. Just tap it out of the way. And then trim off the excess. And we'll snug up the jam nut. And tighten that to 50 foot-pounds.

Put the wheel back on. And the lug nuts. Now we're gonna tighten these lug nuts down to 140 foot-pounds and I'm gonna do it in a cross pattern to tighten the wheel down evenly. And just go around again, double-check.

One of the first things you want to do is safely raise and support your vehicle by the frame so your suspension can hang. Once you've done that, take a small pry bar and we're going to take off this center cap. If you were to spin it, you're going to see a little notch in the cap. Just carefully slide this off of here. That exposes our 22-millimeter lug nuts. Remove all six. Remove your wheel. Now let's remove our 21-millimeter nut. Let's just put that nut on, just a couple threads. Now we're going to take a hammer and we're going to hit right here on the knuckle. You want to be very careful for your brake rotor.

Now that the wheel is off, we have a clear view of where we're going to start working. We're going to disconnect the electrical, this is the ABS right here, and it's very delicate. I'm just gonna come right up along here, and you're gonna see where it's supposed to be mounted to the frame. Should be pretty secure. This is missing about half of its clip, so I'll make sure I secure it in afterward. This purple right here is a little lock, it's holding it from coming separated. I like to just come right in between here, pop that up. Now we'll separate this, just take a peek, make sure you don't see any funny colors. If you were to come right down along here, we're gonna get this clip off of here as well. Just give it a little twist, lift it up, grab that ABS wire, carefully set it aside. The next thing we're going to do is remove this 10-millimeter headed bolt. The next thing we're gonna do is remove the nut that holds the upper ball joint to the knuckle. Okay. That comes right off. I'm just gonna go ahead and put it on there just a couple threads for now. Now let's use a 36-millimeter socket to remove our axle nut. Behind there, there's a washer. Go ahead and remove that as well. Let's go ahead and blast this with some penetrant.

The next thing we need to do is separate the axle from the bearing. I'm going to use this punch right here and go right in the center. You definitely don't wanna use a hammer and potentially damage the threads. The next thing we need to do is remove our mounting bolts that hold the caliper to the knuckle, use an 18-millimeter. Carefully hang your caliper, so it's putting no pressure on your flex hoses. So, now let's just double-check to make sure this upper ball joint nut is still on there a few good threads, it hasn't loosened upon us. And then we'll move down here to the lower ball joint nut. Remove that as well. Take that, and just put it on a couple threads.

Okay, so now it's gonna be time to separate the upper ball joint from the knuckle right here. Pay special attention to anything that's delicate that you don't want ruined, such as an ABS wire. Make sure that that's secure and safely out of the way. Go ahead and take your nice little hammer. And we're going to bonk right here on the knuckle itself. As you can tell it's separated, we can move along. So, now let's push down on this. Remove that nut. And carefully draw this down. Now if you're worried the knuckle with a rotor is going to be too heavy, you can go ahead and use a Torx bit right here, remove that bolt, and take the rotor right off. The problem with removing it like that is you're gonna have to clean up the mating surface between the wheel bearing and the rotor itself. So, now I'm going to take my hammer again and I'm going to come right down here and we're going to hit right on the knuckle itself until this comes down. There we are. Carefully lift up, remove the ball joint nut. Carefully lower this down, remove your knuckle.

The next thing you're going to want to do is support your lower control arm so that you're not putting maximum pressure on your front shock/strut. If you are, you can potentially damage it, because we're going to be using a hammer and we're going to hit right here on the lower ball joint to break it free.

Now to install the lower ball joint, we're gonna want to take the boot off of it first. So, I'm just going to use a nice small screwdriver, pry bar, weasel it in between. Then just kind of separate the two. Be careful not to damage the boot, of course, because we're going to be using it. The next thing we need is a ball joint kit with a cup that's going to fit right up against this lip. We're going to come right underneath, and then we're going to press this right up and in. Right along the bottom. I'm going to use a cup that looks like this, with a hole in the bottom, that's for the stud to go through. It's going to press right up against this ridge right here. Take this cup, something that's hollow enough to make sure that the top part of the ball joint can fit inside. Put it right over the top. Now we're going to take our ball joint C-clamp, put it right over the top, bottom it out. Just check to make sure that the cup is centered to approximately where the ball joints going to be.

Now we're going to tighten this up. As we do that, we want to check this ridge and make sure it matches up directly along this control arm. As you can tell, the ball joint ridge is directly against the control arm right here. Before I release any pressure, I'm just going to give the control arm a couple light bonks with my hammer, just for a little bit of vibration to help make sure this is seated securely. That should be pretty great. Carefully remove your tool. Make sure you install your clamp. To do that, just use these little pliers right here. They fit inside the holes, and then you can spread it. Slide it right over. Make sure it's sitting inside the roof all the way around. If it isn't, just work at it until it is. Now we're going to install our boot. Just carefully bring it up here. I like to try to start it on one side, so I'll go on the side farthest away from me. Then I'll use some pliers and just kind of roll the lip right on. Obviously, be careful not to poke any holes in the boot. Inspect it for any damage. Make sure that it's completely secured. This looks perfect.
Go ahead and take your knuckle. I'm going to start it on the axle a little bit, then slide it over the lower ball joint stud. Lift it up. Kink it to the side and start on that lower ball joint nut. Wiggle the axle around. Should slide right in. Now we're going to use a bar, we're going to pull this upper ball joint down into here. Get the nut, go ahead and start it on there. Just going to take my bar, and try to hold pressure on the lower ball joint to the knuckle. And then we're going to go ahead and try to tighten it up. So, now you'd want to torque this to 37-foot-pounds. If for some reason you can't get your torque wrench in there, like I can't, I would just continue with my wrench and make sure it's nice and tight. [vocalization]. Perfect.

Now it's time to torque up that lower ball joint nut as well. Torque it to 37-foot-pounds. Now what we want to do is make sure that our slot is lined up with the hole that goes through the ball joint stud, so we can make sure we install our cotter pin. Go ahead and slide that through. If for some reason yours is not lined up when you torqued it, you need to continue tightening, not loosening, until it's lined up with the next available slot. Go ahead and peen that over and lock it in. All right. So, now it's gonna be time to get the caliper on here. Just go ahead and slide it right over the rotor. Now we're gonna line up those bolt holes. I like to use some red threadlocker on these bolts. And start them in there. Okay. Let's bottom them out. Now let's go ahead and torque these 248-foot-pounds. Now we'll just go ahead and take that tie rod end, put right through the knuckle. Take your nut, start it on there. We're gonna bottom it out. Now you're gonna torque this to 44-foot-pounds. That's torqued.

The next thing we're gonna do is look to see if we can find the hole in the stud of the tie rod and match it with the next corresponding slot on the tie rod stud nut. This doesn't line up, so what I need to do now is I need to continue tightening until it does. I can see right through. I'm going to grab that locking cotter pin and install it. Slide that right on through and just peen it over. There's no way that this nut can come loose. Now it's going to be time to get the washer with the axle nut on there. Go ahead and slide the pair on. Go ahead and use your 36-millimeter socket, bottom it out, and then we'll torque it. Just gonna put a little splash of never-seize in here, I've got my mounting bolt. Let's use our 10-millimeter and snug it up. Make sure it's fully secured, make sure there's nothing binding your flex hose for your brakes are not twisted in any way.

Now it's time to get our ABS wire re-secured. Let's go ahead and put it in right here. Make sure it cannot come loose. If this can hang around and move around, it could potentially get damaged. Go ahead and connect this in now. Listen for a click, give it a tug. Go ahead and slide in your lock. Now we're going to take our mounting hardware here and just slide it right down in there. It's just a little push clip. Give it a nice tug, make sure it's definitely secured.

So, of course, next, you'd want to go ahead and torque down this nut right here. And that's going to be torqued to 177-foot-pounds. You can do that several ways. If you were to just do it like this, what you're going to notice is it just keeps spinning. If that was the case, what you would do is you can use a pry bar coming straight through these lug studs like this down to the ground. And so it holds it from spinning on you and then you would torque it. If you didn't want to go through the process doing that you can go ahead and throw the wheel up on there and then go through the center hole, which is the way that I'm going to do it.

We'll grab those lug nuts, start them all on there. Let's bottom these out. Now we'll bring it down to the ground and we'll make it so the wheel is just barely touching enough so the wheel can't spin. It's time to torque down this axle nut, 177-foot pounds like I said. Torqued. Now let's do the lug nuts,140-foot-pounds. Go crisscross. Torqued. Now it's gonna be time to get the center cover on. Before you go ahead and pound it on there, just take a look at the back, you're going to see something that looks a lot like a valve stem. Line it up. It's gonna go pretty much just like this. Light bonk, and then, of course, clean up your wheel, make it look nice and pretty and take it for a road test.

Normally, there is a shield right here, you wanna take that shield off. There'll be four or five 15-millimeter bolts. Take that off, get it out of your way. Now, we're gonna take this nut off. On this vehicle, there's a cotter pin. So, I'll just use some side cutters, take this cotter pin off. Just bend it back a little bit and just pry it out. And sometimes they break. There we go. Now, I'm gonna take a 22-millimeter socket, take this nut off. Now, I wanna remove that stud from the steering linkage that goes through the idler arm. I'm gonna use a tool like this, it's gonna press it out. You can use a couple other methods. You could use a pickle fork, try to get it out this way...that way. Just gonna put the nut on to stabilize the tool so it doesn't fall off. All right. While that's on there tight, I'm just gonna give it a tap with the air hammer, see if the vibrations loosen it up. So, that didn't work out. So, I'm gonna try a pickle fork. Sometimes these are tricky to get to separate. There we go.

Now, I'm gonna take these two bolts out. I'm gonna use a 21-millimeter wrench. On the backside, there's a nut and then a 21-millimeter socket on the front. Get that nut off. Take the bolt out. And just grab the idler arm and the housing and just slide it up. If you were gonna replace one of these pieces or the other, you can separate that nut. Just gonna put the housing in the vise, make it easier to install. Take the nut off. All right. Take the idler arm, put the nut on, take a 24-millimeter socket and snug it up. Now, I'm gonna take this castle nut off. And get this in position. As you slide the housing in the bracket, you wanna make sure the idler arm goes through the steering linkage. Get the bolts lined up. And put the nuts on the backside. Now, I'll tighten these down. Then torque both of those bolts to 73 foot-pounds. Now, install the castle nut and tighten that up. And then torque this to 46 foot-pounds. And find the hole through the stud and you can use the cotter pin, slide it through. If it doesn't fit or if you can't get it to line up, you can tighten the nut up a little more so it does line up. There we go. And use some side cutters and just bend this like this. And then you can trim the excess. Now, if you have that shield right here, reinstall that shield.

Before you start, you wanna be aware that after you're done this job, you're gonna wanna go to an alignment specialist so that you can have the vehicle aligned so you don't wear out the tires prematurely.

I'm gonna remove the wheel. Use a 22-millimeter socket. Take the lug nuts off. And take the wheel off. I'm gonna loosen up the jam nut. You can use a 22-millimeter wrench or a 7/8 wrench. Just get that loose. That's good. I'm just gonna spray a little rust penetrant on here. And use an 18-millimeter socket, take this nut off. And if the nut doesn't come off and the stud starts spinning, you can use an 8-millimeter socket to hold that stud from spinning, and then just use the wrench to take the nut off. Now you can take a hammer and just give a tap on the bottom of the tie rod, or take a pickle fork and separate it this way. Just if you use a pickle fork, it's probably gonna rip the boot right here. I'm just gonna give it a hit right here. There we go. And now we're gonna take the outer tie rod off. As we unscrew this, just count the threads. So 1, 2, 3, 4, 23, 24. So write that number down. And when you go to put it back together, you're gonna count them to put the other one in the same position that that one was in.

Now I'm gonna take off the inner tie rod end. I'm gonna use a large adjustable wrench because I don't have a wrench that's big enough to fit this. Slide this over and loosen it up. And eventually we'll get that off. Take the inner tie rod end and get this started. Now we're gonna tighten this up with the adjustable wrench. If you have the ability to torque this, you wanna torque this to 74-foot-pounds. Just do the best you can. That's good. Then you wanna take a grease gun and hook it up to this grease fitting and give it a couple pumps. You can do it until you start seeing the boot move a little bit, then you know there's plenty of grease in there. And take the new tie rod end. Get this started. Make sure you count 1, 2, 3, 4, 5, 22, 23, 24 and line this up in the knuckle. Take the castle nut, get that started. Now, what you can do is to prevent the stud from spinning, you can take a pry bar, just pry in between the knuckle and pry down on the tie rod, use an18-millimeter socket and tighten this up. And tighten this to 37-foot-pounds. And then just check to see where the hole is for the castle nut. And if you need to, you can snug it up a little bit more to get it to line up. And that that hole lines up. Now take the cotter pin, slide it through, actually we'll slide it through this way and take some side cutters and just bend it. Tap it out of the way, and then trim off the excess. And we'll snug up the jam nut and tighten that to 50-foot-pounds. Put the wheel back on and the lug nuts. I'm gonna take these lug nuts down to 140-foot-pounds, and I'm gonna do it in a cross pattern to tighten the wheel down evenly. Just go around again. Double-check.

All right, friends, so one of the first things we need to do is safely raise and support the vehicle. Once you've done that, you want to come right up front to this skid plate right here. Go ahead and remove all 15-millimeter bolts that hold it in. Now that that's out of the way, let's come right over here to where the idler arm comes down through this arm right here. Remove the 21-millimeter nut.

Now, the next thing we would need to do to get this arm out of here is, of course, try to drop this sway bar out of the way. If your bolts look like ours do, and you think that they're going to be an issue, I would just skip right past that, and we'll come right up here, and we'll remove the whole idler unit right here. To get this out of here, we're going to use a 21-millimeter right there, and then we'll use a 21-millimeter wrench on the nut side.

Right there. Let's put a nice piece of wood in between the frame and this bar right here just to make it so this bar can't go up too far while we hammer on this right there. Now that that's out of there, we can grab right onto this, and we'll get it out of the vehicle. Now, when you're replacing the idler arm here, you're going to need to separate it from the idler arm bracket assembly. When you go to do that, you're going to remove this nut right here, and then you're going to have to try to get something in between to try to separate.

You could try to use a puller, and that would probably be helpful if you have that tool. If you don't have the tool, and you try using a pickle fork, you're probably going to damage this right here, in which case, you would replace the pair, which is what we're going to do today. But I'll still show you how to get it apart anyways just in case you're doing only one piece.

Now, to remove this, I like to have it nice and level on the ground, and I'll put my foot on it. I'm going to have it so it's facing down towards the left, so when I remove this and it tries to spin, it can't go anywhere. Now, that we have the nut off of there, we need to separate the idler arm from the bracket assembly itself. We want to do that without damaging the bracket assembly because we're going to be reusing it, right?

So if you were to look right up here, you're going to see that there's a hole right inside the center of this. What I would like to do is take a punch. I'm going to put this on something sturdy. You can use something like a piece of wood like I have now, a desk, a vise, anything you want. Just be super careful. Come right in here with your punch and a hammer. Let's see if we can get this to come out.

Okay. So that came out, and we caused no damage to this. Perfect. The next thing I like to do is put the unit right inside of a vise if you have access to one. You want to grab on to this boot. Take a look underneath there. Make sure there's plenty of grease. Go ahead and push it down. That feels great. Now, we're going to take that idler arm. Set it right down on there. Take our brand-new nut. You always want to use a brand-new nut.

Okay. So now if I use my 24-millimeter wrench, and I try to tighten this, what you're probably going to notice is the stud on the inside is going to start spinning once it gets to a certain point. Okay. So as you can see, it's spinning the stud. Is the nut all the way down? No, it's not. So now we're going to use a hex bit, and you want to use an 8-millimeter. Come right inside there. That's going to hold it, and now we'll continue tightening this.

Make sure it's nice and tight. That feels great. Maybe time to get our unit back up inside the vehicle here. Just bring it right up and in behind those lines hopefully. Okay, get that in the center link. Let's get this into its bracket. Okay, that looks decent. Let's grab our two bolts. Make sure that they have washers. Put that right through. The other one. There we are. Let's grab the washers and the nuts for the other side. Now, let's snug these up. Now, let's go ahead and torque these down to 73 foot-pounds.

Torqued. Let's get this nut on there. Snug it up. Torque this to 46 foot-pounds. Torqued. And use our locking cotter pin. Slide it right on through there, and then make sure you pin it over so there's no way this nut can come loose. This out of here. Awesome. Let's get this shield back up on here. I'm going to line up those holes. Start in all the bolts before I tighten any of them down. Perfect. The next thing that I would want to do is make sure that I get it down to a reputable alignment shop.

You want to keep in mind when you're doing this job, after you're done, you're gonna want to go to a local garage and have the vehicle aligned so you don't have premature tire wear.

Just take this cover off. Use a 15-millimeter socket. There's two bolts in the bottom, two on top. Sometimes there'll be a third. Slide it off. Take this cotter pin out. Just use some side cutters and pull that up. Just gonna use a little rust penetrant. It's a little rusty. Take a 21-millimeter socket. Take this nut off.

Now, I want to separate the idler arm from the steering bar. I'm just gonna use a front-end tool. There's many different tools you could use to get this off. Just tighten this up. Put the nut on just so my tool doesn't slip off the stud. It's just gonna use it as a guide.

Another way you can try to do this is use a pickle fork. There we go. Slide that up. I'm going to take these two bolts out. I'm going to use a wrench, a 21-millimeter wrench backside to hold the nut. Use a 21-millimeter socket on the bolt. Take both of those out. Pull the bolts out. Let me just grab the whole idler arm assembly and you just slide it off.

If you're gonna replace just the arm or just the assembly, you're gonna have to separate it. So use a 24-millimeter socket. It helps to put it in a vise and then you can use a puller and separate these two just like that. And take the arm, put the new nut on. Just snug that up tight. All right, just line this up.

I'm gonna have to tap this in place. That's good. Before you put the bolts through up top, just make sure it's going through this bar right here. Put the bolts in, take the two nuts. Get them on the back side. Now, snug these up. Torque to 74 foot-pounds. And take the castle nut, install that there, tighten it up and torque this to 46 foot-pounds.

If the hole didn't line up, you can just tighten it up a little bit more so you can put the cotter pin in. Slide the cotter pin in, and just bend one of the tabs over and trim the excess. Take this shield, install it bolts, put the back in, and tighten these up.

You wanna keep in mind, when you're doing this job, after you're done, you're gonna wanna go to a local garage and have the vehicle aligned so you don't have premature tire wear.

Disconnect the battery. Disconnect the negative terminal. Use an 8-millimeter wrench. Disconnect that, just slide it out of the way.

You wanna make sure the steering wheel is centered, and you want to lock the steering wheel somehow. What you can do is take the seat belt and just go through the steering wheel and then buckle the seat belt. That way, it'll keep the steering wheel from turning.

All right, take the wheel off. We wanna remove the hubcap. Use a straight-blade screwdriver, slide that off. Use a 22-millimeter socket, take the lug nuts off. Remove the wheel.

I'm gonna take this panel off, use a 15-millimeter socket, take these bolts out. There's four bolts. Slide that down.

Take this cotter pin off. Just use some side cutters. Now, remove this nut. Use a 21-millimeter socket. So, now you can try to use different types of tools to separate this. I'm just gonna use a puller. You can try something like this or you can try something like a pickle fork to try to get it in there.

I'm gonna try to use a pickle fork now. Here we go. We're gonna pull this power steering hose off the steering box right here. You may have a clamp that's holding it on, this one happens to have a worm clamp. Use a 7-millimeter socket. If you have the regular style clamp, just use some pliers. You might wanna put a drain bucket underneath because you're gonna lose some fluid. Take that off.

Now I wanna take this steering line off, use an 18-millimeter wrench. It's not easy to get in there with a wrench. If you have a crows foot, that would work a little better. But just do the best you can.

So, our line is rusted at the top of the steering box and it's not breaking free. In our situation, I'm gonna have to take it off the brake booster. I'm gonna use a 16-millimeter wrench and loosen this up. But, ideally, if you can get it off the top of the box, steering box, then that would be ideal. And I can slide this line out from here. Now I'll just take this line out with the steering box. Just like that. And then, on the top of the steering box, we need to take the linkage that connects this to the lower steering column. There's an 11-millimeter bolt, take that out. Pull that bolt out. It's a good idea to replace this bolt whenever you take it out.

Let's just take a pry bar, get in between the lower steering shaft and your steering box and just pry it up to try to separate the two.

So, I'm gonna try to get this off the rest of the way from underneath. Take your pry bar, try to get in between that groove right there. Just try to hammer it up. All right, that's popped off. It's good.

Now we need to take these three bolts out. There's one behind the shields right there. Use a 21-millimeter socket. Take these out. All right, I'm gonna take the last one out. Just loosen those so they're loose like that.

[inaudible 00:04:53] steering box, just lift it up because you gotta pull that pitman arm out. Twist it sideways so we still have that line connected. And here we go.

Now I'm gonna use a 34-millimeter socket to take this nut off. Take that off. Now this is a dust seal right here. Just get a straight-blade screwdriver and just push it up. Just get that out of the way so we can put our tool on and put the pitman-arm remover on. Here we go.

Now there is four key ways for this to line up. So, install this the same way that the old one came off. Put the lock washer on, put the nut on, and tighten this up. And then do the best you can, put this in a vise and then torque this nut to 180 foot-pounds.

And then slide this dust boot back down. Just like that. Looks good.

Now I'm gonna send the hose up first. You know, if you were able to not have to have the hose connected, then you don't have to do this part. And slide the box in position. You wanna get the pitman arm through that steering bar...just like that. Make sure that's lined up first. Move this around a little bit and get one of these bolts started. And you can try to get the other one started as well. I'm gonna have to rotate this a little bit.

Now I'm gonna torque these bolts to 110 foot-pounds. Now put this nut on. And we're gonna torque this nut to 46 foot-pounds.

Now if the hole's not lined up for the cotter pin, you can tighten the nut a little bit more. It's better to tighten it than loosen it. And that looks good. A little more. Put the cotter pin in. Take some side cutters and just bend it...just like this. And trim the excess.

So, you just wanna make sure that the steering box, the wheels are straight just like it was when you took this shaft off. And just get this lined up. You can get it started while you're underneath. Or you can try to do it from up top.

All right, let's slide the steering shaft onto the box, or the gear. That's lined up. Now you put that bolt in. And do the best you can with torquing this, it might be a little bit better to torque this from underneath. You could get directly on it. You wanna torque that bolt to 37 foot-pounds. Okay, good.

Now I'm gonna run this hose back the way it came, up to the booster. And if you didn't take it off here, connect that hose down below.

All right, now snug this up. Now, if you have the ability to use a torque wrench, you can torque this nut, or the lower nut, on the steering box, to 20 foot-pounds. That's good.

Now install this hose. It goes to the cooler. And tighten this up, if you have a worm clamp, or use the hose clamp pliers. And just snug it up. And this cover, bolt's in. And tighten thee bolts down.

Now let's reconnect the battery. Give it a wiggle, make sure it's tight, and you're good to go.

Now we're gonna top off the fluid, take the cap off of the power steering pump. And then use a funnel, and check your owners manual, put in the appropriate fluid.

All right, so, I over filled this a little bit, which is okay. Now, with the front wheels off the ground and the cap off, you might still wanna put a bucket underneath. I'm gonna turn the wheel back and forth about 20 times. Slowly.

All right, we're gonna double check our fluid level. I haven't started the vehicle yet. And the fluid level's right there. Before I just suck some of the fluid out of there, I'm actually gonna start the vehicle, turn the wheel back and forth a couple times, and then recheck it and adjust accordingly.

Install the tire. Put the lug nuts on. All right, tighten these lug nuts down. I'm going to tighten them in a star pattern, or a cross pattern, to 140 foot-pounds to tighten the wheel down evenly. I'm just go around again, double-check. Take the center cap.